Garmin GPSMAP 3205 - Marine GPS Receiver 설치 지침 매뉴얼
{카테고리_이름} Garmin GPSMAP 3205 - Marine GPS Receiver에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Garmin GPSMAP 3205 - Marine GPS Receiver 10 페이지. Declaration of conformity
Garmin GPSMAP 3205 - Marine GPS Receiver에 대해서도 마찬가지입니다: 빠른 참조 매뉴얼 (2 페이지), 설치 지침 매뉴얼 (17 페이지), 템플릿 매뉴얼 (1 페이지), 중요 안전 정보 (48 페이지), 적합성 선언 (1 페이지)
페이지 인쇄
The GPSMAP 3000 series chartplotter and GPS antenna must be properly installed according to the following instructions. You need the
appropriate fasteners, tools, and mounts listed in each section. These items are available at most marine dealers. Always wear safety goggles,
ear protection, and a dust mask when drilling, cutting, or sanding. When drilling or cutting, always check what is on the opposite side of the
surface. Mount the GPSMAP 3000 series chartplotter in a location that provides a clear, glare-free view of the display and easy operation of the
controls or touch screen. If you experience difficulty installing the chartplotter, seek the assistance of a professional installer; or contact
Garmin
Product Support by phone at 913/397.8200 or 800/800.1020. Go to www.garmin.com/support. In Europe, contact Garmin
®
(Europe) Ltd. at 44/0870.8501241.
Before installing your GPSMAP 3000 series chartplotter, confirm that the package contains the items listed on the box. If any parts are missing,
contact your Garmin dealer immediately.
WARNING: See the Important Safety and Product Information guide in the product box for product warnings and other important
information.
To install the GPSMAP 3000 series chartplotter:
1. Mount the GPSMAP 3000 series chartplotter (Page 1).
2. Mount the GPS antenna (Page 3).
3. Connect the GPSMAP 3000 series device to power and to the GPS antenna (Page 6).
4. Ensure the chartplotter software is up-to-date (Page 10).
Although they are not necessary to use the GPSMAP 3000 chartplotter, you can also use this manual to:
•
Connect the chartplotter to NMEA 0183-compatible devices such as a VHF radio with DSC
•
Connect the chartplotter to an external alarm
•
Connect the chartplotter to a video input source
•
Connect the chartplotter to an external video monitor
•
Connect the chartplotter to other Garmin Marine Network compatible devices, such as a sounder or a radar
You can use the included bracket to bail mount the chartplotter, or you can use the included template and hardware to flush mount the
chartplotter.
Bail Mounting the GPSMAP 3000 Series Chartplotter
Use the included bracket to bail mount the GPSMAP 3000 series chartplotter.
Tools required (not included):
• Drill and drill bit
• Screwdriver
• Pencil
• Mounting hardware (screws or nuts, washers, and bolts)
NotE: The mounting hardware (screws or nuts, washers, and bolts) are not included. The holes on the bail mount are
Choose mounting hardware that fits the holes in the bail mount and securely attaches it to your specific mounting surface. The size of the drill bit
required depends on the mounting hardware chosen.
August, 2008
GPSMAP
3000 Series Installation Instructions
®
(Page
8).
(Page
Mounting the GPSMAP 3000 Series Chartplotter
8).
(Page
8).
190-00991-02 Rev. A
(Page
6).
(Page
9).
/
in. (7.9 mm) in diameter.
5
16
Printed in Taiwan