Garmin GPSMAP 4008 - Marine GPS Receiver 설치 지침 매뉴얼 - 페이지 4

{카테고리_이름} Garmin GPSMAP 4008 - Marine GPS Receiver에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Garmin GPSMAP 4008 - Marine GPS Receiver 25 페이지. Weather and xm satellite radio gpsmap 4000 series; gpsmap 5000 series; gpsmap 6000 series; gpsmap 7000 series
Garmin GPSMAP 4008 - Marine GPS Receiver에 대해서도 마찬가지입니다: 중요 정보 (2 페이지), 소유자 매뉴얼 (2 페이지), 기술 참조 (30 페이지), 빠른 참조 매뉴얼 (2 페이지), 설치 지침 매뉴얼 (19 페이지), 설치 지침 매뉴얼 (25 페이지), 빠른 참조 매뉴얼 (2 페이지), 중요 안전 정보 (48 페이지), 적합성 선언 (1 페이지), 보충 설명서 (24 페이지)

페이지 인쇄

Garmin GPSMAP 4008 - Marine GPS Receiver 설치 지침 매뉴얼

Flush Mounting a GPSMAP 4008/4208/4012/4212/5008/5208/5012/5212 Chartplotter

Flush Mounting a GPSMAP 4010/4210 Chartplotter or a GPSMAP 5015/5215 Chartplotter:

Hardware (included):

• Flush-mount template

• Rubber gasket

• Mounting screws (4.2 × 1.4 DIN7981 / number 8 ANSI)

to flush mount a GPSMAP 4010/4210 chartplotter or a GPSMAP 5015/5215 chartplotter:

1. The flush-mount template is included in the product box. Trim the template and ensure it will fit in the location where you want to flush mount

the chartplotter.

NOTES:

• Make sure the surface on which you mount the chartplotter has at least 7 in. (18 cm) of open space behind it to fit the chartplotter and the

connected wires, and make sure to leave approximately 1/2 in. (13 mm) of space on the right side of the chartplotter to access the SD card

door.

• Mount a 4010/4210 chartplotter 31 1/2 in. (80 cm), and a 5015/5215 chartplotter 23 5/8 in. (60 cm), from a magnetic compass to avoid

interference.

2. The flush-mount template has adhesive on the back. Remove the protective liner and apply

the template to the location at which you want to mount the chartplotter.

3. Using a

in. (10 mm) drill bit, drill a pilot hole inside the corner of the template to begin

cutting the mounting surface.

4. Using the jigsaw, cut the mounting surface along the inside of the solid line indicated on the

flush-mount template. Use a file and sandpaper to refine the size of the hole.

5. If the top and bottom mounting covers are attached to the front of the chartplotter, remove

them by unsnapping the covers from the sides.

Chartplotter

Mounting studs ×4

Rubber gasket

Mounting surface

Lock washers ×4

Flat washers ×4

Hex nuts ×4

tools required (not included):

• Jigsaw

• Masking tape

• Scissors

• Drill

• Drill bits—

in. (10 mm)

• Center punch and hammer

• Anti-seize lubricant (optional)

Mounting covers ×2

GPSMAP 4000/5000 Series Installation Instructions