Garmin GPSMAP 4012 - Marine GPS Receiver 설치 지침 매뉴얼 - 페이지 3

{카테고리_이름} Garmin GPSMAP 4012 - Marine GPS Receiver에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Garmin GPSMAP 4012 - Marine GPS Receiver 19 페이지. Weather and xm satellite radio gpsmap 4000 series; gpsmap 5000 series; gpsmap 6000 series; gpsmap 7000 series
Garmin GPSMAP 4012 - Marine GPS Receiver에 대해서도 마찬가지입니다: 소유자 매뉴얼 (2 페이지), 기술 참조 (30 페이지), 빠른 참조 매뉴얼 (2 페이지), 설치 지침 매뉴얼 (25 페이지), 설치 지침 매뉴얼 (25 페이지), 빠른 참조 매뉴얼 (2 페이지), 중요 안전 정보 (48 페이지), 적합성 선언 (1 페이지), 템플릿 매뉴얼 (2 페이지), 보충 설명서 (24 페이지)

Garmin GPSMAP 4012 - Marine GPS Receiver 설치 지침 매뉴얼
To flush mount the unit:
1. The flush mount template is included in the product box. Trim the template and ensure it will fit in the location you want to flush mount the
unit.
NoTE: Make sure the surface on which you mount the unit has at least 7" (17.75 cm) of open space behind it to fit the unit and the connected
wires.
NoTE: Make sure to leave approximately
NoTE: Mount a 4008/4208/5008/5208 unit 31
interference.
2. The flush mount template has adhesive on the back. Remove the protective liner and apply the template to the location you want to mount
the unit.
3. Using the center punch, indent the center of each of the 4 mm mounting hole locations.
4. Using a 4 mm drill bit, drill the four mounting holes.
5. Using a
/
" (6 mm) drill bit, drill one or more of the four pilot holes inside the corner of the template to begin cutting the mounting surface.
3
8
6. Using the jig saw, cut the mounting surface along the inside of the solid line indicated on the flush mount template. Use a file and
sandpaper to refine the size of the hole. Be very careful when cutting this hole. There is only a small amount of clearance between
the case and the mounting holes.
7. Install the four mounting studs into the unit by screwing the shorter, threaded section into the back of the unit. Use the
wrench to tighten the mounting studs until they stop. Do not overtighten - you may damage the mounting stud or the mounting holes.
The studs are coated with a reusable thread-locking patch applied at the factory.
8. Place the unit into the cut-out. The four mounting studs should feed through the 4 mounting holes drilled in step 3.
9. Place the flat washers, then the lock washers over the mounting studs. Thread the hex nuts onto the mounting studs. Tighten all four hex
nuts evenly until the unit is snug against the mounting surface.
GPSMAP 4000/5000 Series Installation Instructions
1
/
" (13 mm) of space on the right side of the unit to access the SD card door.
2
/
" (80 cm), and a 4012/4212/5012/5212 unit 39
1
4
Flush Mounting the GPSMAP 4000/5000 Series Unit
" (1 m) from a magnetic compass to avoid
/
3
8
/
" (2 mm) Allen
1
16