Garmin GPSMAP 440x - Marine GPS Receiver 빠른 참조 매뉴얼 - 페이지 2

{카테고리_이름} Garmin GPSMAP 440x - Marine GPS Receiver에 대한 빠른 참조 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Garmin GPSMAP 440x - Marine GPS Receiver 2 페이지. Flush mount template
Garmin GPSMAP 440x - Marine GPS Receiver에 대해서도 마찬가지입니다: 설치 지침 매뉴얼 (12 페이지), 적합성 선언 (1 페이지), 설치 지침 매뉴얼 (30 페이지), 템플릿 (1 페이지)

페이지 인쇄

Garmin GPSMAP 440x - Marine GPS Receiver 빠른 참조 매뉴얼

Turning the Unit On or Off

Press and hold the POWER key until the unit beeps and the Garmin

screen appears. When the Warning screen appears, press SELECT to

open the Home screen.

Acquiring GPS Satellite Signals

When you turn on the unit, the GPS receiver must collect satellite data and

establish its current location. If the unit cannot establish a location, the

Initialize Position screen appears.

When the unit acquires satellite signals, the

signal strength bars at the top of the Home screen

are green

. When the unit loses satellite signals, the green bars

disappear

Adjusting the Backlight

To adjust the backlight level:

1. While the unit is on, press and release the

POWER key.

Select Backlight > Manual

Backlight.

To switch between Day and Night

mode:

1. Press and release the POWER key.

Select Day/Night

Mode.

3. Press left or right on the ROCKER to

switch between modes.

POWER/BACKLIGHT—Press and hold to turn the unit on

or off; press and release to adjust the backlight and day/night

modes.

RANGE

(-/+)—Press to adjust the range of the sonar; zoom

in or out on a chart.

ROCKER—Press up, down, left, or right to move through

menus, highlight fields, and enter data.

MARK—Press to mark a waypoint or MOB.

Home Screen

SELECT—Press to select highlighted items and confirm

on-screen messages.

HOME—Press to return to the Home screen.

MENU—Press to access additional settings and configuration options; press to return to the

previous screen when indicated.

Panning the Navigation Chart

Use the map pointer (

) to pan away from your current location and scroll to other areas on

the navigation chart. As you pan past the edge of the current map display, the screen scrolls

forward to provide continuous map coverage. The position icon ( ) stays at your present

Press left or right on the

location.

ROCKER to manually

adjust the backlight.

Map pointer

Position icon

Zooming In and Out on the Map

The

Range (+/-)

keys control the zoom level, indicated by the scale at the bottom of the

navigation chart (

). The bar under the number represents that distance on the map.

Using the Keypad

POWER/

BACKLIGHT

RANGE

ROCKER

MARK

SELECT

HOME

As you move the map pointer, you can view the

distance and bearing from your current location, and

the map pointer's location coordinates in the lower-

right corner of the map.

To pan the map, press up, down, right, or left on the

ROCKER.

To stop panning, press MENU, and then select Stop

Panning.

Creating and Using Routes

To create a route from your present location:

1. Move the map pointer to a destination, and press SELECT.

Select Navigate To > Route

To.

3. Use the ROCKER to add a turn, and press SELECT. Repeat this step

to add additional turns.

4. Press MENU to cancel or to begin navigating the route.

To create a route in another location:

From the Home screen, select Information > User

Data > Routes >

New

Route.

2. Use the ROCKER to select the route's starting point, and press

SELECT.

3. Use the ROCKER and SELECT keys to add additional turns.

4. Press MENU to cancel, edit, or navigate the route.

To edit a route

From the Home screen, select Information > User

Data > Routes.

2. Select the route to edit.

Select Edit

Route. You can edit the route name, turns, or delete the route.

190-00759-01 Rev. A

Garmin Ltd. or its subsidiaries

Printed in Taiwan