Garmin GPSMAP 500 Series 소유자 매뉴얼 - 페이지 16

{카테고리_이름} Garmin GPSMAP 500 Series에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Garmin GPSMAP 500 Series 44 페이지. Flat-mount kit
Garmin GPSMAP 500 Series에 대해서도 마찬가지입니다: 사용 설명서 (6 페이지), 파일럿 매뉴얼 부록 (27 페이지), 빠른 참조 매뉴얼 (2 페이지), 참조 매뉴얼 (2 페이지), 사용 설명서 (28 페이지), 템플릿 (2 페이지), 템플릿 (1 페이지), 구성 매뉴얼 (2 페이지), 빠른 시작 매뉴얼 (4 페이지), 소유자 매뉴얼 (38 페이지), 파일럿 매뉴얼 (28 페이지), 설치 지침 매뉴얼 (34 페이지), 빠른 참조 매뉴얼 (2 페이지)

페이지 인쇄

When using Go To, a direct course and a corrected course may

pass over land or shallow water. Use visual sightings, and steer

to avoid land, shallow water, and other dangerous objects.

NOTE: Auto Guidance is available with premium charts, in

some areas.

Garmin recommends using Guide To only under motor power.

Using Guide To while under sail can cause an unexpected

gybe, risking damage to the sailboat. Unattended sails and

rigging can be damaged or cause injury to any crew or

passengers during an unexpected gybe maneuver.

You can set and follow a course to a destination using one of

three methods: Go To, Route To, or Guide To.

Go To: Takes you directly to the destination. This is the

standard option for navigating to a destination. The

chartplotter creates a straight line course or navigation line to

the destination. The path may run over land and other

obstacles.

Route To: Creates a route from your location to a destination,

allowing you to add turns along the way. This option provides

a straight line course to the destination, but allows you to add

turns into the route that avoid land and other obstacles.

Guide To: Creates a path to a destination using Auto Guidance.

This option is available only when using a compatible

premium chart in a compatible chartplotter. It provides a turn-

by-turn navigation line to the destination, avoiding land and

other obstacles. The navigation line is based on the chart

data and the safe depth, safe height, and shoreline distance

user-defined chartplotter settings. Using these settings and

chart data, the chartplotter creates a navigation line that

avoids all areas that cannot be navigated between the

present location and the destination. When you are using a

compatible Garmin autopilot connected to the chartplotter

using NMEA 2000 ® , the autopilot follows the Auto Guidance

route.

Setting and Following a Direct Course Using Go To

When using Go To, a direct course and a corrected course may

pass over land or shallow water. Use visual sightings, and steer

to avoid land, shallow water, and other dangerous objects.

You can set and follow a direct course from your current

location to a selected destination.

Select a destination (Destinations).

Select Navigate To > Go To.

A magenta line appears. In the center of the magenta line is

a thinner purple line that represents the corrected course

from your current location to the destination. The corrected

course is dynamic, and it moves with your boat when you are

off course.

Follow the magenta line, steering to avoid land, shallow

water, and other obstacles.

If you are off course, follow the purple line (corrected course)

to go to your destination, or steer back to the magenta line

(direct course).

Setting and Following a Course Using Auto Guidance

The Auto Guidance feature is based on electronic chart

information. That data does not ensure obstacle and bottom

clearance. Carefully compare the course to all visual sightings,

and avoid any land, shallow water, or other obstacles that may

be in your path.

CAUTION

NOTE: Auto Guidance is available with premium charts, in

some areas.

Select a destination (Destinations).

Select Navigate To > Guide To.

Review the course indicated by the magenta Auto Guidance

line.

Follow the magenta line, steering to avoid land, shallow

water, and other obstacles.

NOTE: When using Auto Guidance, a gray segment within

any part of the magenta line indicates that Auto Guidance

cannot calculate part of the Auto Guidance line. This is due

to the settings for minimum safe water depth and minimum

safe obstacle height.

Autopilot Navigation

When you start navigation (Go To, Route To, or Guide To), if

you are connected through a NMEA 2000 network to a

compatible Garmin autopilot, you are prompted to engage the

autopilot.

Stopping Navigation

From the Navigation chart or Fishing chart, select Menu >

Stop Navigation.

Waypoints

Waypoints are locations you record and store in the device.

Marking Your Present Location as a Waypoint

From any screen, select Mark.

Creating a Waypoint at a Different Location

Select Nav Info > Waypoints > New Waypoint.

Select an option:

• To create the waypoint by entering position coordinates,

select Enter Coordinates, and enter the coordinates.

• To create the waypoint using a chart, select Use Chart,

select the location, and select Select.

Marking and Starting Navigation to an MOB Location

When you mark a waypoint, you can designate it as a man

overboard (MOB) location.

Select an option:

• From any screen, select Mark > Man Overboard.

• From the Home screen, select Man Overboard > Yes.

An international MOB symbol marks the active MOB point and

the chartplotter sets a direct course back to the marked location.

Viewing a List of all Waypoints

Select Nav Info > Waypoints.

Editing a Saved Waypoint

Select Nav Info > Waypoints.

Select a waypoint.

Select Edit Waypoint.

Select an option:

• To add a name, select Name, and enter a name.

• To change the symbol, select Symbol.

• To change the depth, select Depth.

• To change the water temperature, select Water Temp..

• To change the comment, select Comment.

• To move the position of the waypoint, select Move.

Moving a Saved Waypoint

Select Nav Info > Waypoints.

Select a waypoint.

Navigation with a Chartplotter