Garmin GPSMAP 500 Series 파일럿 매뉴얼 - 페이지 16

{카테고리_이름} Garmin GPSMAP 500 Series에 대한 파일럿 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Garmin GPSMAP 500 Series 28 페이지. Flat-mount kit
Garmin GPSMAP 500 Series에 대해서도 마찬가지입니다: 사용 설명서 (6 페이지), 파일럿 매뉴얼 부록 (27 페이지), 빠른 참조 매뉴얼 (2 페이지), 참조 매뉴얼 (2 페이지), 사용 설명서 (28 페이지), 템플릿 (2 페이지), 템플릿 (1 페이지), 구성 매뉴얼 (2 페이지), 빠른 시작 매뉴얼 (4 페이지), 소유자 매뉴얼 (38 페이지), 소유자 매뉴얼 (44 페이지), 설치 지침 매뉴얼 (34 페이지), 빠른 참조 매뉴얼 (2 페이지)

페이지 인쇄
Garmin GPSMAP 500 Series 파일럿 매뉴얼
SECTION 3
SKYWATCH INTERFACE

User-initiated Test

In addition to the power-up test, the SKYWATCH
performs a continuous self-test. This continuous self-test
is performed several times per minute. A user-initiated
test of the SKYWATCH Interface can also be performed.
NOTE: A user-initiated test can only be performed
when in standby or failed mode.
Performing a user-initiated test:
1)
Turn the small right knob to select the Traffic
Page.
From the Traffic Page, press the MENU Key to
2)
display the Page Menu.
3)
Turn the small right knob to select 'Self
Test?'.
Press the ENT Key.
4)

Voice Announcements

See the SKYWATCH Pilot' s Guide for information on
voice announcements.
3-2
Switching Between Standby and Operating
Modes
The unit must be in operating mode for traffic to be
displayed. The ability to switch out of standby into operating
mode on the ground is especially useful for scanning the
airspace around the airport before takeoff. Operating Mode
is confirmed by the display of 'OPER' in the upper right-
hand corner of the Traffic Page (Figure 3-2).
Switching to Operating Mode from Standby
Mode:
Press the small right knob to activate the
1)
cursor and highlight 'STBY'.
2)
Turn the small right knob to select 'OPER?'.
Press the ENT Key to confirm and place the
3)
SKYWATCH in operating mode, SKYWATCH
switches out of standby into the 6-nm display
range.
NOTE: If the aircraft has a squat switch and the
pilot does not manually switch out of standby,
the SKYWATCH will automatically switch out of
standby 8 to 10 seconds after takeoff.
Switching to Standby Mode from the Traffic
Page:
Press the small right knob to activate the
1)
cursor and highlight 'OPER'.
2)
Turn the small right knob to select 'STBY?'.
3)
Press the ENT Key to confirm and place the
SKYWATCH in standby mode.
NOTE: If the aircraft has a squat switch, STBY is
not displayed while the aircraft is airborne but
will go into standby 24 seconds after landing.
This delay allows the SKYWATCH to remain out
of standby during a touch-and-go maneuver.
400/500 Series Display Interfaces
190-00140-10 Rev. E