Garmin GPSMAP 526s 기술 참조 - 페이지 37

{카테고리_이름} Garmin GPSMAP 526s에 대한 기술 참조을 온라인으로 검색하거나 PDF를 다운로드하세요. Garmin GPSMAP 526s 42 페이지. Flush mount template
Garmin GPSMAP 526s에 대해서도 마찬가지입니다: 설치 지침 매뉴얼 (12 페이지), 참조 매뉴얼 (2 페이지), 중요 안전 정보 (48 페이지), 사용 설명서 (28 페이지), 템플릿 (2 페이지)

페이지 인쇄
Garmin GPSMAP 526s 기술 참조
8. Enter the following command: " " TRIMTABPOS="
9. After the command, enter the percentage of the lowest trim tab position as a whole number between 0 and 100, and select Done. For
example, TRIMTABPOS=100Done.
10. To enter an additional, optional trim tab position, move both trim tabs to a new position, and observe the trim tab position as a percentage of
the full range of motion of the trim tab.
11. Enter the following command: "TRIMTABPOS="
12. After the command, enter the percentage of the trim tab position as a whole number between 0 and 100, and select Done. For example,
TRIMTABPOS=50Done.
13. Repeat steps 10 through 12 to enter additional, optional trim tab positions.
Restoring Factory Default Settings
You will lose all custom configuration settings when you restore factory default settings.
1. From the NMEA 2000 Devices list, select the GBT 10 device.
2. Select an option:
•
For most Garmin chartplotters, select
•
For other Garmin marine devices, select
3. Select Yes.

GST 10 (Garmin Water Speed and Temperature Adapter)

Note: This section provides specific configuration information for the GST 10 adapter using your compatible Garmin display device. To
access the NMEA 2000 configuration menu on your display device, consult the documentation provided with your display device.
Calibrating the Water Speed
To use the GST 10 adapter, you must calibrate the water speed.
1. From the NMEA 2000 Devices list, select the GST 10 device.
2. Select an option:
•
For most Garmin chartplotters, select
•
For other Garmin marine devices, select
3. Follow the on-screen instructions to calibrate the water speed.
Assigning a NMEA 2000 Temperature Source
To use the GST 10 adapter, you must select the source for the temperature data.
1. From the NMEA 2000 Devices list, select the GST 10 device.
2. Select an option:
•
For most Garmin chartplotters, select
•
For other Garmin marine devices, select
3. Select the location of the temperature sensor.
Configuring the Temperature Offset
If the temperature data displayed on the gauge connected to the GST 10 adapter is not the same as temperature data displayed on other devices,
you can configure the temperature offset to increase or decrease the displayed temperature by a specific amount.
1. From the NMEA 2000 Devices list, select the GST 10 device.
2. Select an option:
•
For most Garmin chartplotters, select
•
For other Garmin marine devices, select
3. Select the temperature offset as a positive or negative decimal number, in degrees.
Technical Reference for Garmin NMEA 2000 Products
Review
>
Factory
Defaults.
Config
>
Factory
Defaults.
Review
>
Calibrate Water
Speed.
Config
>
Calibrate Water
Review
>
N2K Temp.
Source.
Config
>
N2K Temp.
Source.
Review
Temperature
Offset.
>
Config
>
Temperature
Offset.
Speed.
NMEA 2000 Checklist