Garmin GPSMAP 6208 설치 지침 매뉴얼 - 페이지 7

{카테고리_이름} Garmin GPSMAP 6208에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Garmin GPSMAP 6208 21 페이지. Weather and xm satellite radio gpsmap 4000 series; gpsmap 5000 series; gpsmap 6000 series; gpsmap 7000 series
Garmin GPSMAP 6208에 대해서도 마찬가지입니다: 소유자 매뉴얼 (2 페이지), 기술 참조 (42 페이지), 적합성 선언 (6 페이지), 템플릿 매뉴얼 (2 페이지), 보충 설명서 (24 페이지), 보충 설명서 (24 페이지)

페이지 인쇄

Installing a locking ring on a cable:

1. Route the cable away from sources of electronic interference so that the cable connector is at the mounting location of the chartplotter.

2. Use the table above to identify the correct locking ring for the cable, and locate the locking ring bag by number.

3. Separate the two halves of the locking ring.

4. Align the two halves of the locking ring over the cable and snap them together.

5. Insert the O-ring into the end of the connector.

Installing Cable Grommets

Depending on the installation, it may be necessary to drill holes to route the connector end of the GPSMAP cables. Rubber grommets are

provided to cover the cable holes for a finished look. You may not need the grommets in some installations. The grommets do NOT create a

waterproof seal. To create a waterproof seal, apply a marine sealant around the

grommet and cable after installation. Be sure to test the system before installing and

sealing the grommets. Purchase additional grommets from your Garmin dealer or

directly from Garmin at

www.garmin.com.

tools Required

• Drill

• 1

in. (31.7 mm) paddle drill bit or hole saw

• Utility knife

• Marine sealant (optional)

to install the cable grommet:

1. Mark the location where you want to route the cable (power, NMEA 0183, NMEA

2000, Marine Video, or Marine Network.)

2. Using a 1

in. (31.7 mm) paddle drill bit or hole saw, drill the installation hole.

3. Refer to the diagram on page 7 for trimming instructions. Carefully trim the cable

hole in the grommet, as needed.

4. Route the cable to the chartplotter, and test the system.

5. Spread the grommet apart at the split and place it around the cable.

6. Firmly push the grommet into the installation hole until it is seated.

7. Apply marine sealant, as needed, to weatherproof the installation-hole (optional).

Wiring the Power Cable

The GPSMAP 6000/7000 series chartplotter must be connected to the power supply for the boat.

1. Route the included 2-pin power cable to the boat battery and to the chartplotter.

2. Connect the power (red) and ground (black) wires to the battery terminals.

NotES:

• Use 14 AWG shielded wiring for extended runs of wire to the power cable.

• Solder all connections and seal them with heat-shrink tubing.

• If your boat has an electrical system, you can possibly wire the chartplotter to an unused holder on your fuse block. If you wire the

chartplotter to the fuse block, remove the in-line fuse holder supplied with the 2-pin power cable.

GPSMAP 6000/7000 Series Installation Instructions

Installing a Locking Ring

Trim to this line for the

Marine Video cable.

Use this hole (no

trim) for a power,

NMEA 0183,

Marine Network, or

NMEA 2000 cable

Split