Garmin GPSMAP 6212 기술 참조 - 페이지 30
{카테고리_이름} Garmin GPSMAP 6212에 대한 기술 참조을 온라인으로 검색하거나 PDF를 다운로드하세요. Garmin GPSMAP 6212 42 페이지. Weather and xm satellite radio gpsmap 4000 series; gpsmap 5000 series; gpsmap 6000 series; gpsmap 7000 series
Garmin GPSMAP 6212에 대해서도 마찬가지입니다: 소유자 매뉴얼 (2 페이지), 설치 지침 매뉴얼 (21 페이지), 적합성 선언 (6 페이지), 템플릿 (2 페이지), 보충 설명서 (24 페이지), 보충 설명서 (24 페이지)
페이지 인쇄
NMEA 2000-Certified Sensor Configuration Information
GRA 10 (Garmin Rudder Angle Adapter)
Note: This section provides specific configuration information for the GRA 10 adapter using your compatible Garmin display device. To
access the NMEA 2000 configuration menu on your display device, consult the documentation provided with your display device.
Calibrating the Rudder Angle
To use the GRA 10 adapter, you must calibrate the angle of the rudder that the adapter is associated with.
1. Turn the boat ignition key to the On position (not Start).
2. From the NMEA 2000 Devices list, select the GRA 10 device.
3. Select an option:
•
For most Garmin chartplotters, select
•
For other Garmin marine devices, select
4. Follow the on-screen instructions to calibrate the starboard and port rudder angles.
5. Select
OK
when the calibration is complete.
Troubleshooting the Gauge Type
When connected to a gauge, the GRA 10 adapter gauge type is set to auto Detect by default, and the adapter automatically detects the type of
gauge it is connected to. If the rudder-angle reading on a connected Garmin chartplotter or marine instrument changes with the engine RPM, the
adapter may be detecting the wrong type of gauge.
To test the gauge-type setting:
1. When the boat is not moving, put the engine in neutral.
2. Use the throttle to increase the engine RPM. If the rudder-angle reading changes with the engine RPM, change the gauge type.
To change the gauge type:
1. From the NMEA 2000 Devices list, select the GRA 10 device.
2. Select an option:
•
For most Garmin chartplotters, select
•
For other Garmin marine devices, select
3. Select an option:
•
To automatically detect the gauge type, select
•
To indicate a one-coil gauge, select
•
To indicate a two-coil gauge, select
4. Perform the gauge-type setting test.
Configuring the GRA 10 Adapter if the Rudder Angle Calibration and Gauge Type Selections Are Not
Displayed
Depending on the version of software loaded on your Garmin marine instrument, the specific configuration options may not be displayed on the
configuration screens.
To calibrate the rudder angle if the menu option is not displayed:
To use the GRA 10 adapter, you must calibrate the angle of the rudder that the adapter is associated with.
1. Turn the boat ignition key to the On position (not Start).
2. From the NMEA 2000 Devices list, select the GRA 10 device.
3. Select an option:
•
For most Garmin chartplotters, select
•
For other Garmin marine devices, select
4. Move the rudder fully to starboard and observe the angle of the rudder position, in degrees.
5. Enter the following command: "RUDDERPOS="
26
Review
>
Rudder Angle
Config
>
Rudder Angle
Review
>
Gauge
Type.
Config
>
Gauge
Type.
Auto
Detect.
1
Coil.
2
Coil.
Review
>
Generic
Config.
Config >Generic
Configuration.
Calibration.
Calibration.
Technical Reference for Garmin NMEA 2000 Products