Garmin GPSMAP 700 Series 소유자 매뉴얼 - 페이지 26

{카테고리_이름} Garmin GPSMAP 700 Series에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Garmin GPSMAP 700 Series 44 페이지. Flat-mount kit
Garmin GPSMAP 700 Series에 대해서도 마찬가지입니다: 설치 지침 매뉴얼 (10 페이지), 빠른 참조 매뉴얼 (2 페이지), 구성 매뉴얼 (2 페이지), 템플릿 (2 페이지), 빠른 시작 매뉴얼 (4 페이지), 소유자 매뉴얼 (38 페이지), 설치 지침 매뉴얼 (6 페이지), 소유자 매뉴얼 (50 페이지), 설치 지침 매뉴얼 (34 페이지)

페이지 인쇄

NOTE: You can optimize the radar display for each radar mode.

Select a radar range

(Range of Radar

Restore the default value of the gain setting

on the Radar Screen

Automatically).

Adjust the gain setting manually

Radar Screen

Manually).

Radar Gain and Clutter

Adjusting Gain on the Radar Screen Automatically

The automatic gain setting for each radar mode is optimized for

that mode, and may differ from the automatic gain setting used

for another mode.

NOTE: Depending upon the radar in use, the gain setting

configured for use in one radar mode may or may not be

applied to other radar modes or to the Radar overlay.

NOTE: Not all options and settings are available on all radar

and chartplotter models.

From a Radar screen or the Radar overlay, select Menu >

Gain.

Condition test. Home Screen not corrected.

Select an available option:

• Select Auto.

The chartplotter sets the gain automatically once, based

on average conditions, the range of the radar signal, and

the selected radar mode. The chartplotter does not adjust

the gain automatically in response to changing conditions.

• Select Auto Harbor or Auto Offshore.

The chartplotter automatically adjusts the gain for the

conditions.

Adjusting Gain on the Radar Screen Manually

For optimal radar performance, you can manually adjust the

gain.

NOTE: Depending upon the radar in use, the gain setting

configured for use in one radar mode may or may not be

applied to other radar modes or to the Radar overlay.

From a Radar screen or the Radar overlay, select Menu >

Gain.

Select Up to raise the gain, until light speckles appear across

the Radar screen.

Data on the Radar screen is refreshed every few seconds.

As a result, the effects of manually adjusting the gain may

not appear instantly. Adjust the gain slowly.

Select Down to lower the gain until the speckles disappear.

If boats, land, or other targets are within range, select Down

to lower the gain until the targets begin to blink.

Select Up to raise the gain until the boats, land, or other

targets appear steadily lit on the Radar screen.

Minimize the appearance of nearby large objects, if

necessary.

Minimize the appearance of side-lobe echoes, if necessary.

Minimizing Nearby Large-Object Interference

Nearby targets of significant size, such as jetty walls, can cause

a very bright image of the target to appear on the Radar screen.

This image can obscure smaller targets located near it.

NOTE: Depending upon the radar in use, the gain setting

configured for use in one radar mode may or may not be

applied to other radar modes or to the Radar overlay.

From a Radar screen or the Radar overlay, select Menu >

Gain.

Select Down to lower the gain until the smaller targets are

clearly visible on the Radar screen.

Signals).

(Adjusting Gain

(Adjusting Gain on the

Reducing the gain to eliminate nearby large-object

interference may cause smaller or distant targets to blink or

disappear from the Radar screen.

Minimizing Side-Lobe Interference on the Radar Screen

Side-lobe interference may appear to streak outward from a

target in a semi-circular pattern. Side-lobe effects can be

avoided by reducing the gain or reducing the radar range.

NOTE: Depending upon the radar in use, the gain setting

configured for use in one radar mode may or may not be

applied to other radar modes or to the Radar overlay.

From a Radar screen or the Radar overlay, select Menu >

Gain.

Select Down to lower the gain until the semi-circular,

streaked pattern disappears from the Radar screen.

Reducing the gain to eliminate side-lobe interference may

cause smaller or distant targets to blink or disappear from

the Radar screen.

Adjusting Sea Clutter on the Radar Screen Automatically

You can set the chartplotter to automatically adjust the

appearance of clutter caused by choppy sea conditions.

NOTE: Depending upon the radar in use, the sea clutter setting

configured for use in one radar mode may or may not be

applied to other radar modes or to the radar overlay.

NOTE: Not all options and settings are available on all radar

and chartplotter models.

From a radar screen or the radar overlay, select Menu >

Noise Rejection > Sea Clutter.

Select Presets or Auto.

Select a setting that reflects the present sea conditions.

When using a compatible radar model, the chartplotter adjusts

the sea clutter based on the sea conditions automatically.

Adjusting Sea Clutter on the Radar Screen Manually

You can adjust the appearance of clutter caused by choppy sea

conditions. The sea clutter setting affects the appearance of

nearby clutter and targets more than it affects the appearance

of distant clutter and targets. A higher sea clutter setting

reduces the appearance of clutter caused by nearby waves, but

it can also reduce or eliminate the appearance of nearby

targets.

NOTE: Depending upon the radar in use, the sea clutter setting

configured for use in one radar mode may or may not be

applied to other radar modes or to the Radar overlay.

From a Radar screen or the Radar overlay, select Menu >

Noise Rejection > Sea Clutter.

Select Up or Down to adjust the appearance of sea clutter

until other targets are clearly visible on the Radar screen.

Clutter caused by sea conditions may still be visible.

Adjusting Rain Clutter on the Radar Screen

You can adjust the appearance of clutter caused by rain.

Reducing the radar range also can minimize rain clutter

of Radar

Signals).

The rain clutter setting affects the appearance of nearby rain

clutter and targets more than it affects the appearance of distant

rain clutter and targets. A higher rain clutter setting reduces the

appearance of clutter caused by nearby rain, but it can also

reduce or eliminate the appearance of nearby targets.

NOTE: Depending upon the radar in use, the rain clutter

settings configured for use in one radar mode may or may not

be applied to other radar modes or to the Radar overlay.

From a Radar screen or the Radar overlay, select Menu >

Noise Rejection > Rain Clutter.

Select Up or Down to decrease or increase the appearance

of nearby rain clutter until other targets are clearly visible on

the Radar screen.

(Range

Radar