Garmin GPSMAP 700 Series 소유자 매뉴얼 - 페이지 27

{카테고리_이름} Garmin GPSMAP 700 Series에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Garmin GPSMAP 700 Series 50 페이지. Flat-mount kit
Garmin GPSMAP 700 Series에 대해서도 마찬가지입니다: 설치 지침 매뉴얼 (10 페이지), 빠른 참조 매뉴얼 (2 페이지), 구성 매뉴얼 (2 페이지), 템플릿 (2 페이지), 빠른 시작 매뉴얼 (4 페이지), 소유자 매뉴얼 (38 페이지), 소유자 매뉴얼 (44 페이지), 설치 지침 매뉴얼 (6 페이지), 설치 지침 매뉴얼 (34 페이지)

페이지 인쇄

screen. Correcting installation issues that cause noise is the

best way to eliminate interference.

Surface Noise: Hides surface noise to help reduce clutter.

Wider beam widths (lower frequencies) can show more

targets, but can generate more surface noise.

Color Gain: See

Adjusting the Level of Detail, page

TVG: Adjusts the appearance of returns to compensate for

weakened sonar signals in deeper water, and reduces the

appearance of noise near the surface. When the value of this

setting is increased, the colors associated with low-level

noise and fish targets appear more consistent through

various water depths. This setting also reduces the noise

near the surface of the water.

Sonar Alarm Settings

NOTE: Some settings require external accessories.

Select Settings > Alarms > Sonar.

Shallow Water: Sets an alarm to sound when the depth is less

than the specified value.

Deep Water: Sets an alarm to sound when the depth is greater

than the specified value.

Water Temp.: Sets an alarm to sound when the transducer

reports a temperature that is 2°F (1.1°C) above or below the

specified temperature.

Fish: Sets an alarm to sound when the device detects a

suspended target.

•

sets the alarm to sound when fish of all sizes are

detected.

•

sets the alarm to sound only when medium or large

fish are detected.

•

sets the alarm to sound only when large fish are

detected.

Transducer Installation Settings

NOTE: Not all options and settings apply to all models, sounder

modules, and transducers.

From a sonar view, select Menu > Sonar Setup > Installation.

Restore Sonar Defaults: Restores the factory default settings

for the sonar view.

Transducer Type: Allows you to select the type of transducer

that is connected to the device.

Shift: Allows you to set the depth range on which the sonar is

focused. This enables you to zoom in to an area within the

focused depth.

Flip Left/Right: Changes the orientation of the SideVü sonar

view when the transducer is installed backward.

Flipped: Sets the orientation of the Panoptix sonar view when

the transducer is installed with the cables pointing toward the

port side of the boat.

Beam Width: Sets the width of the Panoptix transducer beam.

Narrow beam widths allow you to see deeper and farther.

Wider beam widths allow you to see more coverage area.

Use AHRS: Allows the internal attitude heading and reference

system (AHRS) sensors to detect the installation angle of the

Panoptix transducer. When this setting is turned off, it is

assumed the transducer is installed at a 45-degree angle.

Sonar Recordings

Recording the Sonar Display

NOTE: Not all models support sonar recording.

Insert a memory card into the card slot.

From a sonar view, select Menu > Sonar Setup > Sonar

Recording > Record Sonar.

Radar

15 minutes of sonar recording uses approximately 200 MB of

space of the inserted memory card. You can record sonar

until the card reaches capacity.

Stopping the Sonar Recording

Before you can stop recording sonar, you must begin recording

18.

(Recording the Sonar Display, page

From a sonar view, select Menu > Sonar Setup > Sonar

Recording > Stop Recording.

Deleting a Sonar Recording

Insert a memory card into the card slot.

From a sonar view, select Menu > Sonar Setup > Sonar

Recordings > View Recordings.

Select a recording.

Select Delete.

Playing Sonar Recordings

Before you can play back the sonar recordings, you must

download and install the HomePort

sonar data onto a memory card.

Remove the memory card from the device.

Insert the memory card into a card reader attached to a

computer.

Open the HomePort application.

Select a sonar recording from your device list.

Right-click the sonar recording in the lower pane.

Select Playback.

Depth and Water Temperature Graphs

If you are using a depth-capable transducer, or are receiving

water depth information over NMEA

can view a graphic log of depth readings over time. If you are

using a temperature-capable transducer, or are receiving water

temperature information over NMEA 0183 or NMEA 2000, you

can view a graphic log of temperature readings over time.

The graphs scroll to the left as information is received.

Select Sonar > Data Graphs.

Setting the Depth and Water Temperature Graph

Range and Time Scales

You can indicate the amount of time and the range of depth that

appear in the depth and water temperature graphs.

Select Sonar > Data Graphs > Menu.

Select Depth Graph Settings or Temperature Graph

Settings.

Select an option:

• To set a time-elapsed scale, select Duration. The default

setting is 10 minutes. Increasing the time-elapsed scale

allows you to view variations over a longer period of time.

Decreasing the time-elapsed scale allows you to view

more detail over a shorter period of time.

• To set the depth-range or temperature-range scale, select

Scale. Increasing the scale allows you to view more

variation in readings. Decreasing the scale allows you to

view more detail in the variation.

The marine radar transmits microwave energy that has the

potential to be harmful to humans and animals. Before

beginning radar transmission, verify that the area around the

radar is clear. The radar transmits a beam approximately 12°

above and below a line extending horizontally from the center of

the radar.

21).

™

application and record

0183 or NMEA 2000, you

Radar

WARNING