Garmin GPSMAP 7015 기술 참조 - 페이지 38

{카테고리_이름} Garmin GPSMAP 7015에 대한 기술 참조을 온라인으로 검색하거나 PDF를 다운로드하세요. Garmin GPSMAP 7015 42 페이지. Weather and xm satellite radio gpsmap 4000 series; gpsmap 5000 series; gpsmap 6000 series; gpsmap 7000 series
Garmin GPSMAP 7015에 대해서도 마찬가지입니다: 소유자 매뉴얼 (2 페이지), 설치 지침 매뉴얼 (21 페이지), 중요 안전 정보 (48 페이지), 적합성 선언 (6 페이지), 템플릿 매뉴얼 (2 페이지), 보충 설명서 (24 페이지)

페이지 인쇄
Garmin GPSMAP 7015 기술 참조
NMEA 2000 Checklist
4. Select Done.
Troubleshooting the Sensor Number
If multiple GST 10 adapters are assigned to the same NMEA 2000 temperature source, each adapter is assigned a unique sensor number
automatically. If the "Invalid NMEA 2000 temperature configuration" error message appears, you must assign a unique sensor number to each
adapter.
For example, if two adapters are assigned the NMEA 2000 temperature source value of Live Well and the error message appears, you must
assign each adapter a unique number.
1. From the NMEA 2000 Devices list, select the GST 10 device.
2. Select an option:
•
For most Garmin chartplotters, select
•
For other Garmin marine devices, select
3. Select a sensor number.
4. Select OK.
Configuring the GST 10 Adapter if the Water Speed, Location, Temperature Offset, and Sensor Number
Selections Are Not Displayed
Depending on the version of software loaded on your Garmin marine instrument, the specific configuration options may not be displayed on the
configuration screens.
To calibrate the water speed if the menu option is not displayed:
To use the GST 10 adapter, you must calibrate the water speed.
1. From the NMEA 2000 Devices list, select the GST 10 device.
2. Select an option:
•
For most Garmin chartplotters, select
•
For other Garmin marine devices, select
3. Ensure that the boat is stationary; the engine should be off or idling.
4. Enter the following command: " " WATERSPEED=0Done"
5. Accelerate the boat to cruising speed and observe the maximum speed, in miles per hour.
6. Bring the boat to a stop; the engine should be off or idling.
7. Enter the following command: " " WATERSPEED="
8. After the command, enter a positive decimal number that indicates the maximum cruising speed in miles per hour, followed by Done. For
example, WATERSPEED=35.5Done.
To configure the temperature source if the location menu option is not displayed:
To use the GST 10 adapter, you must select the source for the temperature data.
1. From the NMEA 2000 Devices list, select the GST 10 device.
2. Select an option:
•
For most Garmin chartplotters, select
•
For other Garmin marine devices, select
3. Enter the following command: "TEMPSOURCE="
4. After the command, enter a number between 0 and 8, or 13, to indicate the source of the temperature data as defined in the following table,
followed by Done.
For example, TEMPSOURCE=6Done indicates that the bait well is the source for the temperature data.
Review
>
Sensor
Number.
Config
>
Sensor
Number.
Review
>
Generic
Config.
Config >Generic
Configuration.
Review
>
Generic
Config.
Config >Generic
Configuration.
Technical Reference for Garmin NMEA 2000 Products