Garmin GPSMAP 8000 Series 설치 지침 매뉴얼 - 페이지 8

{카테고리_이름} Garmin GPSMAP 8000 Series에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Garmin GPSMAP 8000 Series 14 페이지. Installation instructions
Garmin GPSMAP 8000 Series에 대해서도 마찬가지입니다: 소유자 매뉴얼 (36 페이지), 빠른 시작 매뉴얼 (4 페이지), 사용 설명서 (15 페이지), 소유자 매뉴얼 (43 페이지)

페이지 인쇄

Item

Description

NMEA 0183-compliant device

NMEA 0183 cable

Item

• If the NMEA 0183-compliant device has only one input (RX) wire (no A, B, +, or -), leave the pink wire unconnected.

• If the NMEA 0183-compliant device has only one output (TX) wire (no A, B, +, or -), connect the orange/white wire to ground.

• Consult the installation instructions of your NMEA 0183-compliant device to identify the output A(+) and B(-) wires and input A(+)

and B(-) wires.

• Use 28 AWG, shielded, twisted-pair wiring for extended runs of wire.

• Solder all connections and seal them with heat-shrink tubing.

Advanced NMEA 0183 Connections

There are four internal NMEA 0183 input ports (RX ports), and two internal NMEA 0183 output (TX ports) on the included NMEA

0183 data cable. You can connect one NMEA 0183 device per internal RX port to input data to your Garmin device, and you can

connect up to three NMEA 0183 devices in parallel to each internal TX port to receive data output by your Garmin device. Each

internal RX and TX port has 2 wires, labeled A (+) and B (-) according to the NMEA 0183 convention. The corresponding A (+) and

B (-) wires of each internal port should be connected to the A (+) and B (-) wires of your NMEA 0183-compliant device. Refer to the

table and wiring diagrams when connecting the data cable to NMEA 0183 devices.

Consult the installation instructions for your NMEA 0183-compliant device to identify the output (TX) A (+) and B (-) wires and input

(RX) A (+) and B (-) wires. Use 28 AWG, shielded, twisted-pair wiring for extended runs of wire. Solder all connections and seal

them with heat-shrink tubing.

• For two-way communication with a NMEA 0183 device, the internal ports on the NMEA 0183 data cable are not linked. For

example, if the input of the NMEA-compliant device is connected to the internal output port 1 on the data cable, you can connect

the output port of your NMEA 0183-compliant device to any of the internal input ports (port 1, port 2, port 3, or port 4) on the

wiring harness.

• The ground wires on the NMEA 0183 data cable and your NMEA 0183-compliant device must both be connected to ground.

• See

Specifications, page 13

• The internal NMEA 0183 ports and communication protocols are configured on the connected Garmin device. See the NMEA

0183 section or communication configuration section of the owner's manual provided with your Garmin device for more

information.

Port

Input port 1

Input port 2

Input port 3

Garmin Wire Function

Power

Power ground

Data ground

Receive B (-)

Receive A (+)

Transmit A (+)

Transmit B (-)

for a list of the approved NMEA 0183 sentences output by and input to your device.

Wire Function

RX/A (+)

RX/B (-)

RX/A (+)

RX/B (-)

RX/A (+)

RX/B (-)

Garmin Wire Color

Red

Black

Orange/white

White

Gray

Pink

Wire Color

White

Orange/white

Brown

Brown/white

Violet

Violet/white

GPSMAP 8000 Series Installation Instructions

NMEA 0183 Device Wire Function

Power

Power ground

Data ground

N/A

Transmit

Receive

N/A

Pin Number