Garmin GPSMAP 8700 설치 지침 매뉴얼 - 페이지 3

{카테고리_이름} Garmin GPSMAP 8700에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Garmin GPSMAP 8700 6 페이지.
Garmin GPSMAP 8700에 대해서도 마찬가지입니다: 설치 지침 매뉴얼 (27 페이지), 설치 지침 매뉴얼 (8 페이지)

Garmin GPSMAP 8700 설치 지침 매뉴얼
• Devices earlier than the GPSMAP 8000 series and GPSMAP
8500 series cannot be used in a station.
• Although it is not necessary, it is recommended that you
install all of the devices you plan to use in one station near
each other.
• No special connections are necessary to create a station, as
long as all of the devices are connected to the Garmin Marine
Network
(Garmin Marine Network Considerations, page
• Stations are created and modified using the device software.
See the owner's manual provided with the device for more
information.
GMM Monitor Connection Considerations
You can use a GMM monitor to view and control the GPSMAP
8700. When connecting a GMM monitor to the GPSMAP 8700
device, you must observe these considerations.
• The touchscreen functionality of the GMM monitor can be
used to control one GPSMAP 8700 device.
• Although it is recommended to use Garmin DVI-D cables,
high-quality third-party DVI-D cables may be used. Before
you route a DVI-D cable, you should connect all devices to it
for testing.
• You must use an HDMI to DVI-D cable or adapter.
• You must connect the GMM monitor to the same power
source as the GPSMAP 8700 device. If this is not possible,
you must connect the devices to the same ground.
• You must connect the GMM monitor to a NETWORK port on
the GPSMAP 8700 device or to the same Garmin Marine
Network as the GPSMAP 8700 device.
• The touch data is sent over the Garmin Marine Network.
Item Device or port
GPSMAP chartplotter
GMM touchscreen monitor
Chartplotter's HDMI OUT port
GMM monitor's MAIN DVI VIDEO IN
port
GMM monitor's GARMIN
PROCESSOR BOX port
Chartplotter's NETWORK port or the
Garmin Marine Network
Third-Party Touchscreen Connection Considerations
When connecting a third-party touchscreen to view and control
the GPSMAP 8700 device, you must observe these
considerations.
• The video data is sent over the HDMI connection.
• The touch data is sent over the USB connection.
2).
NOTE: If the monitor is not a touchscreen, you should install a
GRID remote control (not a GRID 20 remote control).
NMEA 2000 Considerations
If you are connecting to an existing NMEA 2000 network,
identify the NMEA 2000 power cable. Only one NMEA 2000
power cable is required for the NMEA 2000 network to operate
properly.
A NMEA 2000 Power Isolator (010-11580-00) should be used in
installations where the existing NMEA 2000 network
manufacturer is unknown.
If you are installing a NMEA 2000 power cable, you must
connect it to the boat ignition switch or through another in-line
switch. NMEA 2000 devices will drain your battery if the NMEA
2000 power cable is connected to the battery directly.
This device can connect to a NMEA 2000 network on your boat
to share data from NMEA 2000 compatible devices such as a
GPS antenna or a VHF radio. The included NMEA 2000 cables
and connectors allow you to connect the device to your existing
NMEA 2000 network. If you do not have an existing NMEA 2000
network you can create a basic one using cables from Garmin.
If you are unfamiliar with NMEA 2000, you should read the
"NMEA 2000 Network Fundamentals" chapter of the Technical
Reference for NMEA 2000 Products. You can find this document
using the "Manuals" link on the product page for your device at
www.garmin.com.
The port labeled NMEA 2000 is used to connect the device to a
Cable
standard NMEA 2000 network.
DVI-D cable with an
HDMI adapter
Garmin Marine Network
Cable
Item Device or port
GPSMAP chartplotter
Third-party touchscreen monitor
Chartplotter's HDMI OUT port
Monitor's HDMI IN port
Monitor's USB port
Chartplotter's USB HOST port
Item
Description
NMEA 2000 compatible Garmin device
GPS antenna
Ignition or in-line switch
NMEA 2000 power cable
NMEA 2000 drop cable
Cable
Garmin HDMI Cable
Garmin OTG Adapter Cable
NOTICE
3