Garmin GPSMAP 902 series 설치 지침 매뉴얼 - 페이지 4
{카테고리_이름} Garmin GPSMAP 902 series에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Garmin GPSMAP 902 series 8 페이지.
Garmin GPSMAP 902 series에 대해서도 마찬가지입니다: 설치 지침 매뉴얼 (9 페이지)
페이지 인쇄
switch. NMEA 2000 devices will drain your battery if the NMEA
2000 power cable is connected to the battery directly.
This device can connect to a NMEA 2000 network on your boat
to share data from NMEA 2000 compatible devices such as a
GPS antenna or a VHF radio. The included NMEA 2000 cables
and connectors allow you to connect the device to your existing
NMEA 2000 network. If you do not have an existing NMEA 2000
network you can create a basic one using cables from Garmin.
If you are unfamiliar with NMEA 2000, you should read the
"NMEA 2000 Network Fundamentals" chapter of the Technical
Reference for NMEA 2000 Products. You can find this document
using the "Manuals" link on the product page for your device at
www.garmin.com.
The port labeled NMEA 2000 is used to connect the device to a
standard NMEA 2000 network.
Item
Description
NMEA 2000 compatible Garmin device
GPS antenna
Ignition or in-line switch
NMEA 2000 power cable
NMEA 2000 drop cable
12 Vdc power source
NMEA 2000 terminator or backbone cable
NMEA 2000 T-connector
NMEA 2000 terminator or backbone cable
NMEA 0183 Connection Considerations
• There is one internal NMEA 0183 input port (RX port) and
one internal NMEA 0183 output port (TX port) on the included
NMEA 0183 data cable. You can connect one NMEA 0183
device to the internal RX port to input data to this Garmin
device, and you can connect up to three NMEA 0183 devices
in parallel to the internal TX port to receive data output by this
Garmin device.
• See the installation instructions for the NMEA 0183 device to
identify the transmit (TX) and receive (RX) wires.
• The device provides one TX port and one RX port. Each
internal port has 2 wires, labeled A and B according to the
NMEA 0183 convention. The corresponding A and B wires of
each internal port should be connected to the A (+) and B (-)
wires of the NMEA 0183 device.
• You must use 28 AWG, shielded, twisted-pair wiring for
extended runs of wire. Solder all connections and seal them
with heat-shrink tubing.
• Do not connect the NMEA 0183 data wires from this device
to power ground.
• The power cable from this device and the NMEA 0183
devices must be connected to a common power ground.
4
• For two-way communication with a NMEA 0183 device, the
internal ports on the NMEA 0183 data cable are not linked.
For example, if the input of the NMEA 0183 device is
connected to TXA on the data cable, you can connect the
output port of your NMEA 0183 device to the input port on the
wiring harness.
• See
NMEA 0183 Information, page 6
approved NMEA 0183 sentences that are output by and input
to this device.
• The internal NMEA 0183 ports and communication protocols
are configured on the connected Garmin device. See the
NMEA 0183 section of the chartplotter owner's manual for
more information.
NMEA 0183 Device Connections
This diagram illustrates two-way connections for both sending
and receiving data. You can also use this diagram for one-way
communication. To receive information from a NMEA 0183
device, refer to items
,
Garmin device. To transmit information to a NMEA 0183 device,
refer to items
,
,
, and
device.
Item
Description
Power source
Power/NMEA 0183 cable
NMEA 0183 device
Item
Garmin Wire
Function
Power
Power ground
Not applicable
RXA
RXB
TXA
TXB
Single-Ended NMEA 0183 Device Connections
Item
Description
Power source
Power/NMEA 0183 cable
NMEA 0183 device
Item
Garmin Wire
Function
Power
Power ground
for a list of the
,
, and
when connecting the
when connecting the Garmin
Garmin Wire
NMEA 0183
Color
Device Wire
Function
Red
Power
Black
Power ground
Not applicable
Data ground
Brown
TXA
Violet
TXB
Blue
RXA
Gray
RXB
Garmin Wire
NMEA 0183
Color
Device Wire
Function
Red
Power
Black
Power ground