Garmin nuvi 500-Series 소유자 매뉴얼 - 페이지 28

{카테고리_이름} Garmin nuvi 500-Series에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Garmin nuvi 500-Series 50 페이지. Flush mount template
Garmin nuvi 500-Series에 대해서도 마찬가지입니다: 빠른 참조 매뉴얼 (2 페이지), 사용자 설명서 (28 페이지), 소유자 매뉴얼 (38 페이지), 중요 정보 (1 페이지), 소유자 매뉴얼 (44 페이지), 설치 지침 매뉴얼 (6 페이지)

페이지 인쇄

When the radar is transmitting, do not look directly at the

antenna at close range; eyes are the most sensitive part of the

body to electromagnetic energy.

NOTE: Not all models support radar.

When you connect your compatible chartplotter to an optional

Garmin marine radar, such as a GMR

HD, you can view more information about your surroundings.

The GMR transmits a narrow beam of microwave energy as it

rotates to a 360° pattern. When the transmitted energy contacts

a target, some of that energy is reflected back to the radar.

Radar Display Modes

NOTE: Not all modes are available with all radar devices and all

chartplotters.

Select Radar.

Cruising Mode: Shows a full-screen image of the gathered

radar information.

Harbor Mode: Intended for use in inland waters, this mode

works best with short-range signals (2 nm or less).

Offshore Mode: Intended for use in open waters, this mode

works best with long-range signals.

Sentry Mode: Allows you to put the radar into timed-transmit

mode, in which you can configure a radar transmit and

standby cycle to conserve power. You can also enable a

guard zone in this mode, which identifies a safe zone around

your boat. If you switch from Sentry mode to another mode,

the radar switches to full-time transmission and disables all

guard zones.

Radar Overlay Mode: Shows a full-screen image of the

gathered radar information on top of the Navigation chart.

The Radar overlay displays data based on the most recently

used radar mode.

Transmitting Radar Signals

NOTE: As a safety feature, the radar enters standby mode after

it warms up. This gives you an opportunity to verify the area

around the radar is clear before beginning radar transmission.

With the chartplotter off, connect your radar as described in

the radar installation instructions.

Turn on the chartplotter.

The radar warms up and a countdown alerts you when the

radar is ready.

Select Radar.

Select a radar mode.

A countdown message appears while the radar is starting up.

Select Menu > Transmit Radar.

Adjusting the Radar Range

The range of the radar signal indicates the length of the pulsed

signal transmitted and received by the radar. As the range

increases, the radar transmits longer pulses in order to reach

distant targets. Closer targets, especially rain and waves, also

reflect the longer pulses, which can add noise to the Radar

screen. Viewing information about longer-range targets can also

decrease the amount of space available on the Radar screen for

viewing information about shorter-range targets.

• Select

to decrease the range.

• Select

to increase the range.

Tips for Selecting a Radar Range

• Determine what information you need to see on the Radar

screen.

1226 xHD2 or a GMR 24

™

For example, do you need information about nearby weather

conditions or targets and traffic, or are you more concerned

about distant weather conditions?

• Assess the environmental conditions where the radar is being

used.

Especially in inclement weather, longer-range radar signals

can increase the clutter on the Radar screen and make it

more difficult to view information about shorter-range targets.

In rain, shorter-range radar signals can enable you to view

information about nearby objects more effectively, if the rain

clutter setting is configured optimally.

• Select the shortest effective range, given your reason for

using radar and the present environmental conditions.

Adjusting the Zoom Scale on the Radar

Screen

The radar zoom scale, also called the radar signal range,

represents the distance from your position (the center) to the

outermost ring.

From a Radar screen, select

Each ring represents an even division of the zoom scale.

For example, if the zoom scale is set at 3 miles, each ring

represents 1 mile from the center out.

Marking a Waypoint on the Radar Screen

From a Radar screen or the Radar overlay, select a location.

Select New Waypoint.

Sentry Mode

Sentry mode allows you to put the radar into timed-transmit

mode, in which you can configure a radar transmit and standby

cycle to conserve power. You can also enable a guard zone in

this mode, which identifies a safe zone around your boat and

sounds an alarm when a radar object enters the zone. Sentry

mode works with some Garmin GMR model radars.

Enabling Timed Transmit

From the sentry screen, select Menu > Sentry Setup >

Timed Transmit > On.

Setting the Standby and Transmit Times

Before you can set the standby and transmit times, you must

enable timed transmit

(Enabling Timed Transmit, page

To help conserve power, you can indicate the radar standby

time and the transmit time to implement periodic radar signal

transmissions at set intervals.

From the sentry screen, select Menu > Sentry Setup.

Select Stdby Time.

Enter the time interval between radar signal transmissions.

Select Transmit Time.

Enter the duration of each radar signal transmission.

Enabling a Guard Zone

From the sentry screen, select Menu > Sentry Setup >

Enable Guard Zone.

Defining a Circular Guard Zone

Before you can define the boundaries of the guard zone, you

must enable a guard zone

You can define a circular guard zone that completely

encompasses your boat.

From the sentry screen, select Menu > Sentry Setup >

Adjust Guard Zone > Move Radar Guard Zone > Circle.

Select the location of the outer guard zone circle.

Select the location of the inner guard zone circle to define the

width of the guard zone.

(Enabling a Guard Zone, page

22).

Radar