Garmin Cessna Caravan G1000 파일럿 매뉴얼 - 페이지 11

{카테고리_이름} Garmin Cessna Caravan G1000에 대한 파일럿 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Garmin Cessna Caravan G1000 34 페이지. Integrated flight deck
Garmin Cessna Caravan G1000에 대해서도 마찬가지입니다: 파일럿 매뉴얼 (16 페이지), 파일럿 매뉴얼 (6 페이지), 파일럿 매뉴얼 (32 페이지), 파일럿 매뉴얼 (25 페이지), 파일럿 매뉴얼 (21 페이지), 비행기 비행 매뉴얼 보충 자료 (33 페이지), 파일럿 매뉴얼 (22 페이지)

페이지 인쇄

1.4 COLOR CODE

Frequencies located in the active ﬁ eld are displayed

in either green or white.

• An active frequency that is displayed in green

indicates that the corresponding radio is selected

(i.e., in use).

• An active frequency that is displayed in white

indicates that the corresponding radio is not

selected.

Frequencies located in the standby ﬁ eld are displayed

in either white or gray.

• The standby frequency that appears in the tuning

box is displayed in white.

• The standby frequency that is not in the tuning

box is displayed in gray.

NOTE: In GPS mode, both active NAV frequencies

are displayed in white.

NOTE: In split COM mode, both active COM

frequencies are displayed in green.

1.5 TUNING BOX

On both the PFD and the MFD, a cyan tuning box ap-

pears over the standby frequency ﬁ eld and can be moved

from one standby frequency ﬁ eld to another for the pur-

pose of tuning or radio selection.

In both the COM and NAV windows, the frequency

toggle arrow appears next to the tuning box, between the

active and standby frequencies.

Frequency Toggle Arrow

Figure 1-3 Frequency Toggle Arrow and Tuning Box

190-00302-01 Page Rev. 1

G1000_COM-NAV_PG.indd 3

1.6 FREQUENCY TOGGLE ARROW

A Frequency Toggle Arrow appears between the two

frequencies of the radio sub-window on which the fre-

quency tuning box is located. Pressing the dual COM or

NAV knob toggles both the frequency tuning box and the

Frequency Toggle Arrow between the radios.

1.7 RADIO STATUS INDICATIONS

• RX – When a signal is received on a COM radio,

a white RX indication appears to the right of the

corresponding COM frequency for the duration of

the signal reception.

• TX – When a microphone is keyed, a white TX

indication appears to the right of the correspond-

ing COM frequency for the duration of the signal

transmission.

• ID – When the VOL/PUSH ID knob is pressed, a

white ID indication appears to the left of the NAV

frequency on the selected NAV sub-window and

the Morse code identiﬁ er audio for the selected

VOR frequency can be heard if the corresponding

NAV radio is selected on the audio panel.

Frequency Tuning Box

Garmin G1000 VHF NAV/COM Pilot's Guide

OPERATION – COM

NOTE: If the frequency tuning box is on a

selected COM sub-window when a signal

is received or transmitted for this radio, the

Frequency Toggle Arrow is replaced by an

RX or a TX indication, respectively.

NOTE: When the desired frequency is entered in

the tuning box, it becomes a standby frequency.

Pressing the Frequency Toggle key places this

standby frequency into the active ﬁ eld, and vice

versa.

Garmin Proprietary

2/10/2004, 8:47:24 AM