Garmin GPSMAP 527xs Guide 소유자 매뉴얼 - 페이지 22

{카테고리_이름} Garmin GPSMAP 527xs Guide에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Garmin GPSMAP 527xs Guide 38 페이지. Technical reference for garmin nmea 2000 products
Garmin GPSMAP 527xs Guide에 대해서도 마찬가지입니다: 설치 지침 매뉴얼 (12 페이지), 참조 매뉴얼 (2 페이지), 사용자 설명서 (28 페이지), 제품 정보 (37 페이지), 사용 설명서 (28 페이지), 템플릿 (2 페이지), 적합성 선언 (6 페이지), 구성 매뉴얼 (2 페이지), 참조 (42 페이지), 빠른 시작 매뉴얼 (4 페이지), 설치 지침 매뉴얼 (8 페이지)

페이지 인쇄

Marking a Waypoint on the Radar Screen

From a Radar screen or the Radar overlay, select a location.

Select Create Waypoint.

Viewing a List of AIS Threats

From any Radar screen or the Radar overlay, you can view and

customize the appearance of a list of AIS threats.

From a Radar screen or the Radar overlay, select Menu >

Other Vessels > AIS List.

Showing AIS Vessels on the Radar Screen

AIS requires the use of an external AIS device and active

transponder signals from other vessels.

You can configure how other vessels appear on the Radar

screen. If any setting (except the AIS display range) is

configured for one radar mode, the setting is applied to every

other radar mode. The details and projected heading settings

configured for one radar mode are applied to every other radar

mode and to the Radar overlay.

From a Radar screen or the Radar overlay, select Menu >

Other Vessels > AIS Display Setup.

Select an option:

• To indicate the distance from your location within which

AIS vessels appear, select AIS Display Range, and

select a distance.

• To show details about AIS-activated vessels, select

Details > Show.

• To set the projected heading time for AIS-activated

vessels, select Projected Heading, and enter the time.

• To show the tracks of AIS vessels, select Trails, and

select the length of the track that appears.

VRM and EBL

The variable range marker (VRM) and the electronic bearing

line (EBL) measure the distance and bearing from your boat to

a target object. On the Radar screen, the VRM appears as a

circle that is centered on the present location of your boat, and

the EBL appears as a line that begins at the present location of

your boat and intersects the VRM. The point of intersection is

the target of the VRM and the EBL.

Showing the VRM and the EBL

The VRM and the EBL configured for one mode are applied to

all other radar modes.

From a Radar screen, select Menu > Show VRM/EBL.

Adjusting the VRM and the EBL

Before you can adjust the VRM and the EBL, you must show

them on the Radar screen

You can adjust the diameter of the VRM and the angle of the

EBL, which moves the intersection point of the VRM and the

EBL. The VRM and the EBL configured for one mode are

applied to all other radar modes.

From a Radar screen, select a new location for the

intersection point of the VRM and the EBL.

Select Drop VRM/EBL.

Select Stop Pointing.

Measuring the Range and Bearing to a Target Object

Before you can adjust the VRM and the EBL, you must show

them on the Radar screen

From a Radar screen, select the target location.

Select Measure Distance.

The range and the bearing to the target location appear in

the upper-left corner of the screen.

(page

16).

(page

16).

Radar Overlay

When you connect your chartplotter to an optional Garmin

marine radar, you can use the Radar overlay to overlay radar

information on the Navigation chart or on the Fishing chart.

The Radar overlay superimposes radar information on the

Navigation chart or the Fishing chart. Data appears on the

Radar overlay based on the most recently used radar mode

(such as Harbor, Offshore, or Sentry), and all settings

configurations applied to the Radar overlay are also applied to

the last-used radar mode. For example, if you use Harbor mode

and then you switch to the Radar overlay, the Radar overlay

would show Harbor mode radar data. If you changed the gain

setting using the Radar overlay menu, the gain setting for

Harbor mode would change automatically.

Radar Overlay and Chart Data Alignment

When using the Radar overlay, the chartplotter aligns radar data

with chart data based on the boat heading, which is based by

default on data from a magnetic heading sensor connected

using a NMEA 0183 or NMEA 2000 network. If a heading

sensor is not available, the boat heading is based on GPS

tracking data.

GPS tracking data indicates the direction in which the boat is

moving, not the direction in which the boat is pointing. If the

boat is drifting backward or sideways due to a current or wind,

the Radar overlay may not perfectly align with the chart data.

This situation should be avoided by using boat-heading data

from an electronic compass.

If the boat heading is based on data from a magnetic heading

sensor or an automatic pilot, the heading data could be

compromised due to incorrect setup, mechanical malfunction,

magnetic interference, or other factors. If the heading data is

compromised, the Radar overlay may not align perfectly with

the chart data.

Showing the Radar Overlay

The Radar overlay displays data based on the most recently

used radar mode.

Select Radar > Radar Overlay.

The radar picture appears in orange and overlays the

Navigation chart.

Stopping the Transmission of Radar Signals

From the Radar screen, select Menu > Radar to Standby.

Optimizing the Radar Display

You can adjust the radar display settings for reduced clutter and

increased accuracy.

NOTE: You can optimize the radar display for each radar mode.

Select a radar range

(page

Restore the default value of the gain setting

Adjust the gain setting manually

Range of Radar Signals

The range of the radar signal indicates the length of the pulsed

signal transmitted and received by the radar. As the range

increases, the radar transmits longer pulses in order to reach

distant targets. Closer targets, especially rain and waves, also

reflect the longer pulses, which can add noise to the Radar

screen. Viewing information about longer-range targets can also

decrease the amount of space available on the Radar screen

for viewing information about shorter-range targets.

Radar Gain and Clutter

Automatically Adjusting Gain on the Radar Screen

Auto is the default value for the gain setting. The automatic gain

setting for each Radar mode is optimized for that mode, and

16).

(page

16).

(page

17).

Radar