Garmin GPSMAP 76 series 설치 지침 매뉴얼 - 페이지 2
{카테고리_이름} Garmin GPSMAP 76 series에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Garmin GPSMAP 76 series 9 페이지. Gpsmap 76 series
Garmin GPSMAP 76 series에 대해서도 마찬가지입니다: 적합성 선언 (1 페이지), 사양 시트 (2 페이지), 빠른 참조 매뉴얼 (2 페이지)
페이지 인쇄
2
Using a drill bit appropriate for your mounting hardware, drill
the pilot holes.
3
Secure the bail mount bracket to the surface using your
mounting hardware
.
4
Install the bail mount knobs
5
Place the device in the bail mount bracket, and tighten the
bail mount knobs.
Flush Mounting the Device
Be careful when cutting the hole to flush mount the device.
There is only a small amount of clearance between the case and
the mounting holes, and cutting the hole too large could
compromise the stability of the device after it is mounted.
The included template and hardware can be used to flush mount
the device in your dashboard.
1
Trim the template, and make sure it fits in the location where
you want to mount the device.
2
Secure the template to the selected location.
1
3
Using a 13 mm (
/
in.) drill bit, drill one or more of the holes
2
inside the corners of the solid line on the template to prepare
the mounting surface for cutting.
4
Using a jigsaw or a rotary tool, cut the mounting surface
along the inside line on the template.
5
Place the device in the cutout to test the fit.
6
If necessary, use a file and sandpaper to refine the size of
the cutout.
7
After the device fits correctly in the cutout, ensure the
mounting holes on the device line up with the larger 7.2 mm
5
(
/
in.) holes on the template.
16
8
If the mounting holes on the device do not line up, mark the
new hole locations.
5
9
Using a 7.2 mm (
/
in.) drill bit, drill the larger holes.
16
10
Starting in one corner of the template, place a nut plate
over the larger hole
1
The smaller 3.5 mm (
/
line up with the smaller hole on the template.
11
1
If the smaller 3.5 mm (
line up with the smaller hole on the template, mark the new
hole location.
12
Repeat steps 10 and 11 to verify placement of the remaining
nut plates and holes on the template.
2
on the sides of the device.
NOTICE
drilled in step 9.
in.) hole
on the nut plate should
8
/
in.) hole on the nut plate does not
8
1
13
Using a 3.5 mm (
/
in.) drill bit, drill the smaller holes.
8
14
Remove the template from the mounting surface.
15
Starting in one corner of the mounting location, place a nut
plate
on the back of the mounting surface, lining up the
large and small holes.
The raised portion of the nut plate should fit into the larger
hole.
16
Secure the nut plate to the mounting surface by fastening an
included M3 screw
through the smaller 3.5 mm (
hole.
17
Repeat steps 15–16 to secure the remaining nut plates to the
mounting surface.
18
Install the rubber gasket
The pieces of the rubber gasket have adhesive on the back.
Make sure you remove the protective liner before installing
them on the device.
19
If you will not have access to the back of the device after you
mount it, connect all necessary cables to the device before
placing it into the cutout.
NOTE: To prevent corrosion of the metal contacts, cover
unused connectors with the attached weather caps.
20
Apply marine sealant between the mounting surface and the
device to properly seal and prevent leakage behind the
dashboard.
21
If you will have access to the back of the device, apply
marine sealant around the cutout.
22
Place the device into the cutout.
23
Secure the device to the mounting surface using the included
M4 screws
.
24
Wipe away all excess marine sealant.
25
Install the decorative bezel by snapping it in place around the
edges of the device.
Cable and Connection Considerations
• The cables may have been packaged without the locking
rings installed. If so, you should route the cables before you
install the locking rings.
• After connecting a locking ring to a cable, make sure the ring
is securely connected and the O-ring is in place so the
connection remains secure.
Power/NMEA
0183 Cable
®
• The wiring harness connects the device to power, NMEA
0183 devices, and a lamp or a horn for visible or audible
alerts.
• If it is necessary to extend the NMEA 0183 or alarm wires,
you must use 22 AWG (.33 mm²) wire.
1
/
8
on the back of the device.
in.)