Garmin Mobile 20 설치 지침 매뉴얼 - 페이지 5

{카테고리_이름} Garmin Mobile 20에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Garmin Mobile 20 15 페이지. Garmin cell phone - mobile phone user manual
Garmin Mobile 20에 대해서도 마찬가지입니다: 설치 지침 매뉴얼 (12 페이지), 수동 설정 및 이동 (20 페이지), 적합성 선언 (1 페이지), 빠른 참조 매뉴얼 (2 페이지), 적합성 선언 (1 페이지), 사양 (2 페이지), 소유자 매뉴얼 (29 페이지), (핀란드어) 사용자 설명서 (20 페이지)

페이지 인쇄

Mounting the Scanner

1. Once a suitable mounting location has been determined, verify that the mounting hole locations are aligned fore and aft, then drill four

9.5 mm (0.37") mounting holes referencing Figure 1 below. (This step is not necessary if you are using a pre-drilled Garmin compatible

or Raymarine mount.)

2. Remove the supplied M8x30 bolts, ﬂat washers, and spring washers (4 each) from the bottom of the scanner unit. Do NOT remove the

outer case bolts. There are no user serviceable parts in the scanner and opening the case may void your warranty.

3. Align the notch and locking ring on the Power Cable to the power connector. Press the 2-pin Power Cable to the power connector and

the RJ-45 Marine Network Cable to the RJ-45 socket (Figure 2). Turn the Power Cable locking ring clockwise until it stops. Tighten the

RJ-45 locking ring clockwise until it is ﬁrmly sealed.

4. The Power/Network Cable may be pressed into one of the three guide grooves moulded into the bottom of the scanner case (Figure 2).

Avoid excessive bending or twisting of the cable. See the following "Cable Runs" section for more information.

5. Position the scanner on the mounting surface with the triangular marks on the case aligned to the front of the vessel and the rounded

marks aligned towards aft (Figure 2). A bead of marine sealant may be applied around each of the mounting holes on the mounting

surface.

6. Fasten the scanner to the mounting surface using the M8x1.25x30 hex bolts, spring washers, and ﬂat washer and shoulder washers

in the order show in Figure 3. The supplied M8x1.25x30 bolts, ﬂat washers, and spring washers (4 each) may be used on mounting

thicknesses of 5-10 mm (3/8") (recommended). For surfaces over 10 mm (3/8"), locally supplied longer bolts are needed. The bolts

should be torqued to between 13.7-18.6 N m (10-14 lb ft).

Cable Runs

Route the cable as needed, depending on the type of mount you are using. Do NOT cut the cable! It may be necessary to drill a 31.7 mm

(1.25") hole for routing the Power/Network cable. Garmin provides a rubber Cable Grommet which may be used to cover the cable installation

hole. The grommet does NOT provide a waterproof seal. You may choose to apply a marine sealant after installation to weatherproof around the

grommet and cable. Additional Cable Grommets may be purchased through Garmin or your Garmin dealer.

When installing the Power/Network Cable, observe the following:

• To ensure safety, use the appropriate tie-wraps, fasteners, and sealant to secure the cable along a route and through any bulkhead or deck.

Avoid running the cable near moving objects, high heat sources, or through doorways and bilges.

• Avoid installing the cable next to or in parallel other cables such as, radio antenna lines or power cables. This is essential to avoid

interference to/from other equipment. If this is not possible, shield the cable with metal conduit or a form of EMI shielding.

• Install the Power portion of the cable as close to the battery source as possible. A minimum of 10 v D.C. is required at the 15 m cable

connector during radar turn-on and operation. See table below for recommended wire gauge between radar cable and battery.

Up to:

2 meters (6.5 ft)

16 AWG

4 meters (13 ft)

14 AWG

6 meters (19 ft)

12 AWG

Wire Gauge Table

233.0 mm

(9.17")

O 9.5 mm

(0.37")

Figure 1

GMR 20/40 Radar Installation Instructions

Power

Mounting

Network

Connector

RJ-45 Port

Bow

Mark

Figure 2

Stern

Holes

Mark

Cable Guide

Grooves

Scanner

Mounting

Bracket

Shoulder

Washer

Flat

Washer

Spring

M8x30

Bolt

Figure 3