Garmin NMEA 2000 기술 참조 - 페이지 3
{카테고리_이름} Garmin NMEA 2000에 대한 기술 참조을 온라인으로 검색하거나 PDF를 다운로드하세요. Garmin NMEA 2000 20 페이지. Technical reference for garmin nmea 2000 products
Garmin NMEA 2000에 대해서도 마찬가지입니다: 설치 지침 매뉴얼 (10 페이지), 데이터시트 (1 페이지), 기술 참조 (30 페이지), 기술 참조 (42 페이지), 사용 설명서 (20 페이지), 설치 지침 매뉴얼 (40 페이지), 참조 (42 페이지)
페이지 인쇄
Item
Description
Not
Field-installable
pictured
connector
NMEA 2000 Glossary
Backbone: This is the main communication path of the NMEA 2000 network. The backbone can be as simple
as three T-connectors connected side to side with terminators on both ends, or can expand to include many
T-connectors separated by backbone cables. The backbone must always be constructed in a linear manner
for the network to function properly
Backbone Cable: Backbone cables extend the NMEA 2000 backbone to connect NMEA 2000 devices located in
different places on the boat. The maximum length of a single backbone cable is 100 m (328 ft.). Backbone
cables must connect to the sides of two T-connectors to maintain linear backbone construction, and must
never connect to the top of a T-connector
Device: Electronic hardware that connects to the NMEA 2000 network. A device may only transmit data to the
network, receive data transmitted by other devices on the network, or may both transmit and receive data on
the network.
Drop Cable: A cable connecting an NMEA 2000 device to the NMEA 2000 backbone. Drop cables are limited to
6 m (20 ft.) maximum length. Drop cables must connect to the top of a T-connector or to the side of an in-
line terminator
(Linear Backbone Construction, page
In-line Terminator: A special terminator that can be used in place of a male terminator (not available as a
female connector), that allows direct connection to the a device at the end of the NMEA 2000 backbone. The
inline terminator simplifies installation by not requiring a T-connector, male terminator, and drop cable for
the device at the end of the backbone
LEN (Load Equivalency Number): A simplified value that represents the amount of current a device draws from
the NMEA 2000 network. A LEN of 1 = 50 mA. Each device should have an LEN specified on the product or in
the product documentation that you should use when calculating the power needs and balance of your
NMEA 2000 network
Network Power: 12 Vdc power supplied to the NMEA 2000 network. Power to the NMEA 2000 network should
be connected through a switch (instead of directly connected to the battery) because some NMEA 2000
devices are always on when power is present, and this may drain the battery. NMEA 2000 devices must
operate from 9 to 16 Vdc, with a nominal voltage of 12 Vdc
Terminator: A 120 ohm resistor located at each end of the NMEA 2000 backbone. Proper termination is
required to ensure signal integrity across the entire length of the backbone
page
6).
T-connector: A three-way connector with one male and two female micro connectors. A T-connector is used to
connect an NMEA 2000 device to the NMEA 2000 backbone.
Garmin Part Number
010-11094-00: male
010-11095-00: female
(Linear Backbone Construction, page
(Linear Backbone Construction, page
(Network Termination, page
(Power Distribution and Balance, page
Notes
Can be used to create a backbone or drop cable for
a custom length.
Can be used to shorten any Garmin NMEA 2000
backbone or drop cable
6).
6).
11).
8).
(Linear Backbone Construction, page
(Linear Backbone Construction,
6).
6).
3