Garmin Reactor 40 설치 지침 매뉴얼

{카테고리_이름} Garmin Reactor 40에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Garmin Reactor 40 11 페이지. Mechanical
Garmin Reactor 40에 대해서도 마찬가지입니다: 설치 지침 매뉴얼 (13 페이지), 설치 지침 매뉴얼 (29 페이지), 구성 매뉴얼 (8 페이지), 설치 지침 매뉴얼 (25 페이지)

페이지 인쇄

1. Installation Procedures

REACTOR™ 40 HYDRAULIC

Installation Instructions

Important Safety Information

See the Important Safety and Product Information guide in the

product box for product warnings and other important

information.

You are responsible for the safe and prudent operation of your

vessel. The autopilot is a tool that enhances your capability to

operate your boat. It does not relieve you of the responsibility of

safely operating your boat. Avoid navigational hazards and

never leave the helm unattended.

Always be prepared to promptly regain manual control of your

boat.

Learn to operate the autopilot on calm and hazard-free open

water.

Use caution when operating the autopilot near hazards in the

water, such as docks, pilings, and other boats.

When in use, beware of hot motor and solenoid components

and the risk of entrapment from moving parts.

Failure to install and maintain this equipment in accordance with

these instructions could result in damage or injury.

To avoid damage to your boat, the autopilot system should be

installed by a qualified marine installer. Specific knowledge of

hydraulic steering componentry and marine electrical systems is

required for proper installation.

Registering Your Device

Help us better support you by completing our online registration

today. Keep the original sales receipt, or a photocopy, in a safe

place.

Go to

my.garmin.com/registration

Installation Preparation

The autopilot system consists of multiple components. You

should familiarize yourself with all of the component mounting

and connection considerations before beginning installation. You

must know how the components operate together in order to

correctly plan the installation on your boat.

You can consult the layout diagrams

page

2) to help understand the mounting and connection

considerations.

You should lay out all of the components on the boat as you

plan the installation to make sure your cables will reach each

component. If needed, extension cables (sold separately) for

various components are available from your Garmin dealer or

from www.garmin.com.

You should record the serial number of each component for

registration and warranty purposes.

Tools Needed

• Safety glasses

• Drill and drill bits

• 90 mm (3.5 in.) hole saw or a rotary cutting tool (for installing

an optional helm control)

• Wire cutters/strippers

• Phillips and flat screwdrivers

WARNING

CAUTION

NOTICE

account.

(Power and Data Layout,

• Cable ties

• Waterproof wire connectors (wire nuts) or heat-shrink tubing

and a heat gun

• Marine sealant

• Portable or handheld compass (to test for magnetic

interference)

NOTE: Mounting screws are provided for the main components

of the autopilot system. If the provided screws are not

appropriate for the mounting surface, you must provide the

correct types of screws.

Mounting and Connection Considerations

The autopilot components connect to each other and to power

using the included cables. Ensure that the correct cables reach

each component and that each component is in an acceptable

location before mounting or wiring any components.

CCU Mounting and Connection Considerations

• The CCU is the primary sensor of the Reactor 40 Hydraulic

autopilot system. For best performance, observe these

considerations when selecting a mounting location.

◦ A handheld compass should be used to test for magnetic

interference in the area where the CCU is to be

mounted(Testing a Location for Magnetic Interference,

page

1).

◦ The CCU should be mounted on a rigid surface for best

performance.

• Mounting screws are provided with the CCU. If you use

mounting hardware other than the provided screws, the

hardware must be quality stainless or brass material to avoid

magnetic interference with the CCU.

Test any mounting hardware with a handheld compass to

make sure no magnetic fields are present in the hardware.

• The CCU cable connects the CCU to the ECU and is 5 m

(16 ft.) long.

◦ If the CCU cannot be mounted within 5 m (16 ft.) of the

ECU, extension cables are available from your local

Garmin dealer or at www.garmin.com.

◦ This cable must not be cut.

Finding the Best Mounting Location

Create a list of all suitable mounting locations for the CCU.

Suitable mounting locations should not be within 60 cm (2 ft.)

of the following:

• Iron

• Magnets

• High-current wires

• Intermittently-running pumps, such as head pumps and

live well pumps

A large magnet, such as a subwoofer-speaker magnet,

should be no closer than 1.5 m (5 ft.) to any of the mounting

locations.

Locate the center of rotation of the boat, and measure the

distance between the center of rotation and each of the

suitable mounting locations you listed in step 1.

Select the location closest to the center of rotation.

If more than one location is approximately the same distance

from the center of rotation, you should select the location that

best meets these considerations.

• The best location is closest to the centerline of the boat.

• The best location is lower in the boat.

• The best location is slightly forward in the boat.

Testing a Location for Magnetic Interference

You can use a handheld compass to test a mounting location for

magnetic interference.

Hold a handheld compass in the CCU mounting location.

October 2017

190-02315-02_0A