Garmin STRIKER PLUS 4 소유자 매뉴얼 - 페이지 13

{카테고리_이름} Garmin STRIKER PLUS 4에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Garmin STRIKER PLUS 4 16 페이지. Ice fishing kit
Garmin STRIKER PLUS 4에 대해서도 마찬가지입니다: 설치 지침 매뉴얼 (16 페이지)

페이지 인쇄

Beeper: Turns on and off the tone that sounds for alarms and

selections

(Setting the Beeper, page

GPS: Provides information about the GPS satellite settings and

fix.

Auto Power: Turns on the device automatically when power is

applied.

Keyboard Layout: Sets the arrangement of the keyboard to an

alphabetical or computer keyboard layout.

Language: Sets the on-screen language.

System Information: Provides information about the device and

the software version.

Simulator: Turns on the simulator and allows you to set the

speed and simulated location.

System Information

Select Settings > Settings > System Information.

Event Log: Allows you to view a log of system events.

Software Information: Provides information about the device

and the software version.

Garmin Devices: Provides information about connected Garmin

devices.

Factory Settings: Restores the device to factory settings.

NOTE: This deletes any setting information you have

entered.

My Vessel Settings

NOTE: Some settings and options require additional hardware.

Some settings are available only when you have valid depth

data.

Select Settings > My Vessel.

Transducer Type: Displays the type of transducer connected to

the device

(Selecting the Transducer Type, page

Keel Offset: Offsets the surface reading for the depth of a keel,

making it possible to measure depth from the bottom of the

keel instead of from the transducer location

Offset, page

11).

Temp. Offset: Compensates for the water temperature reading

from a temperature-capable transducer

Temperature Offset, page

Setting the Keel Offset

You can enter a keel offset to compensate the water depth

reading for the transducer installation location. This allows you

to view the depth of the water below the keel or the true depth of

the water, depending on your needs.

If you want to know the water depth below the keel or the lowest

point of your boat and the transducer is installed at the water

line or anywhere above the end of the keel, measure the

distance from the transducer location to the keel of the boat.

If you want to know the true water depth and the transducer is

installed below the water line, measure the distance from the

bottom of the transducer up to the water line.

NOTE: This option is only available when you have valid depth

data.

Measure the distance:

• If the transducer is installed at the water line

anywhere above the end of the keel, measure the

distance from the transducer location to the keel of the

boat. Enter this value as a positive number.

• If the transducer is installed at the bottom of the keel

and you want to know the true depth of the water,

measure the distance from the transducer to the water

line. Enter this value in as a negative number.

Device Configuration

2).

4).

(Setting the Keel

(Setting the Water

11).

Select Settings > My Vessel > Keel Offset.

Select

if the transducer is installed at the water line, or

select

if the transducer is installed at the bottom of the

keel.

Use the arrow keys to enter the keel offset measured in step

Setting the Water Temperature Offset

You can set the temperature offset to compensate for the

temperature reading from a temperature-capable sensor.

Measure the water temperature using the temperature-

capable transducer that is connected to the device.

Measure the water temperature using a different

thermometer or temperature sensor that is known to be

accurate.

Subtract the water temperature measured in step 1 from the

water temperature measured in step 2.

This is the temperature offset. Enter this value in step 5 as a

positive number if the sensor connected to the device

measures the water temperature as being colder than it

actually is. Enter this value in step 5 as a negative number if

the sensor connected to the device measures the water

temperature as being warmer than it actually is.

Select Settings > My Vessel > Temp. Offset.

Use the arrow keys to enter water temperature offset

measured in step 3.

Alarms Settings

Navigation Alarms

Select Settings > Alarms > Navigation.

Arrival: Sets an alarm to sound when you are within a specified

distance or time from a turn or a destination.

Anchor Drag: Sets an alarm to sound when you exceed a

specified drift distance while anchored.

Off Course: Sets an alarm to sound when you are off course by

a specified distance.

System Alarms

Alarm Clock: Sets an alarm clock.

Device Voltage: Sets an alarm to sound when the battery

reaches a specified low voltage.

GPS Accuracy: Sets an alarm to sound when the GPS location

accuracy falls outside the user-defined value.

Sonar Alarms

Select Settings > Alarms > Sonar.