Fujitsu 12RLS3H 설치 매뉴얼 - 페이지 5

{카테고리_이름} Fujitsu 12RLS3H에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Fujitsu 12RLS3H 6 페이지. Outdoor unit

페이지 인쇄

BENDING PIPES

(1) When bending the pipe, be careful not to crush it.

(2) To prevent breaking of the pipe, avoid sharp bends.

Bend the pipe with a radius of curvature of 70 mm or over.

(3) If the copper pipe is bend the pipe or pulled to often, it will become stiff. Do not

bend the pipes more than three times at one place.

Holding spanner

Body side

90°

Torque wrench

Table 1

Flare nut tightening torque

Flare nut [mm (in.)]

6.35 (1/4) dia.

9.52 (3/8) dia.

12.70 (1/2) dia.

Table 2

Pipe outside diameter

Pipe outside diameter [mm (in.)]

6.35 (1/4)

9.52 (3/8)

12.70 (1/2)

Fasten a ﬂ are nut with a torque wrench as instructed in this manual. If fastened too

tight, the ﬂ are nut may be broken after a long period of time and cause a leakage of

refrigerant.

Install heat insulation around both the gas and liquid pipes. Failure to do so may cause

water leaks.

Use heat insulation with heat resistance above 248 °F. (Reverse cycle model only)

In addition, if the humidity level at the installation location of the refrigerant piping is

expected to exceed 70%, install heat insulation around the refrigerant piping. If the

expected humidity level is 70-80%, use heat insulation that is 15 mm or thicker and if

the expected humidity exceeds 80%, use heat insulation that is 20 mm or thicker.

If heat insulation is used that is not as thick as speciﬁ ed, condensation may form on the

surface of the insulation.

In addition, use heat insulation with heat conductivity of 0.045 W/(m·K) or less (at 68 °F).

5.5. Vacuum

(1) Remove the cap, and connect the gauge manifold and the vacuum pump to the

charging valve by the service hoses.

(2) Vacuum the indoor unit and the connecting pipes until the pressure gauge

indicates -0.1 MPa (-76 cmHg).

(3) When -0.1 MPa (-76 cmHg) is reached, operate the vacuum pump for at least

30 minutes.

(4) Disconnect the service hoses and ﬁ t the cap to the charging valve to the speciﬁ ed

torque.

(5) Remove the blank caps, and fully open the spindles of the 2-way and 3-way

valves with a hexagon wrench [Torque: 2.9 N·m (30 kgf·cm)].

(6) Tighten the blank caps of the 2-way valve and 3-way valve to the speciﬁ ed torque.

Tightening torque [N

Blank cap

6.35 mm (1/4 in.)

9.52 mm (3/8 in.)

12.70 mm (1/2 in.)

Charging port cap

Connecting pipe

Outdoor unit

Service hose

with valve core

3-way valve

Charging port

Cap

To prevent gas leakage, coat the ﬂ are

surface with refrigerator oil.

Tightening torque [N

m (lbf

ft)]

•

16 to 18 (11.8 to 13.3)

32 to 42 (23.6 to 31.0)

49 to 61 (36.1 to 45.0)

A [mm (in.)]

Flare tool for R410A, clutch type

0 to 0.5 (0 to 1/32)

CAUTION

m (lbf

ft)]

•

20 to 25 (14.8 to 18.4)

28 to 32 (20.7 to 23.6)

10 to 12 (7.4 to 8.8)

Blank cap

Hexagon wrench

Use a 4 mm

hexagon wrench.

Gauge manifold

Vacuum pump

Service hose

Do not purge the air with refrigerants, but use a vacuum pump to vacuum the

installation.

There is no extra refrigerant in the outdoor unit for air purging.

Use a vacuum pump and gauge manifold and charging hose for R410A exclusively.

Using the same vacuum for different refrigerants may damage the vacuum pump or the

unit.

ADDITIONAL CHARGE

When moving and installing the air conditioner, do not mix gas other than the

speciﬁ ed refrigerant R410A inside the refrigerant cycle.

When charging the refrigerant R410A, always use an electronic balance for refrig-

erant charging (to measure the refrigerant by weight).

When charging the refrigerant, take into account the

slight change in the composition of the gas and liquid

phases, and always charge from the liquid phase side

whose composition is stable.

Add refrigerant from the charging valve after the comple-

tion of the work.

If the units are further apart than the maximum pipe length, correct operation can-

not be guaranteed.

GAS LEAKAGE INSPECTION

After connecting the piping, check the all joints for gas leakage with gas leak detector.

When inspecting gas leakage, always use the vacuum pump for pressure. Do not use

nitrogen gas.

5.7. TEST RUN

 Perform test operation and check items below.

 For the test operation method, refer to the operating manual.

 The outdoor unit, may not operate, depending on the room temperature. In this

case, keep on pressing the MANUAL AUTO button of the indoor unit for more than

10 seconds. The operation indicator lamp and timer indicator lamp will begin to ﬂ ash

simultaneously during cooling test run. Then, heating test run will begin in about three

minutes when HEAT is selected by the remote control operation. (Please follow the

operating manual for remote control operation.)

 To end test operation, keep on pressing the MANUAL AUTO button of the indoor unit for

more than 3 seconds.

(When the air conditioner is run by pressing the MANUAL AUTO button, the OPERA-

TION indicator lamp and TIMER indicator lamp of the indoor unit will simultaneously

ﬂ ash slowly.)

OUTDOOR UNIT

(1) Is there any abnormal noise and vibration during operation?

(2) Will noise, wind, or drain water from the unit disturb the neighbors?

(3) Is there any gas leakage?

Always turn on the power 12 hours prior to the start of the operation in order to

ensure compressor protection.

CAUTION

Use a clean gauge manifold

and charging hose for R410A

exclusively.

CAUTION

Gas

R410A

Liquid

CAUTION

En-5