Fujitsu 3NGF70811 운영 매뉴얼 - 페이지 6
{카테고리_이름} Fujitsu 3NGF70811에 대한 운영 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Fujitsu 3NGF70811 15 페이지.
페이지 인쇄
3.3. Inserting batteries
Battery type: R03/LR03/AAA x 2
1
2
9
5
1
Pull the cover in the direction of the arrow and open it
until it is trapped.
2
Remove the cover.
① Turn the remote controller over and push the back
side of the cover and remove the claws by curving
the cover.
② Pull in the direction of the arrow while curving the
cover.
3
Put batteries as shown in the figure above.
4
Press "RESET" as shown in the figure above.
Use the tip of a ballpoint pen or other small object.
5
Press
to start setting day of the week and clock.
(
)
6
Press
Sunday).
7
Press
to continue.
(
)
8
Press
Press the buttons to change the clock by a minute.
Press and hold the buttons to change the clock by 10 minutes.
* To switch the time indicator (12-hour ⇔ 24-hour), press
.
Press
to complete the setting.
9
Be close to the indoor unit. If you press the button from a
distance, settings may not be properly sent.
10
Install and close the cover.
NOTES:
• Use specified type of batteries only.
• Do not mix different types or new and used batteries together.
• Batteries can be used about 1 year in ordinary use.
• If the remote control range noticeably shortens, replace the
batteries, and press
En-5
3
7
6
RESET
8
4
to set day of the week (Monday to
to set the clock.
as shown in the figure above.
4. BASIC OPERATIONS
■ 3 steps to start operation
1. Press
to start or stop the operation.
2. Press
to select the operation mode.
The operation mode changes as follows.
AUTO
COOL
3. Press
to set the desired temperature.
The temperature changes by 0.5 °C increments.
Temperature setting range
Auto/Cooling/Dry
Heating
NOTES:
• In the Cooling or Dry mode, set the temperature lower than the
current room temperature.
• In the Heating mode,
- set the temperature higher than the current room temperature.
- at the beginning of the operation, the indoor unit fan rotates at very
low speed for 3-5 minutes.
- the Automatic defrosting operation overrides the Heating operation
when necessary.
• In the Fan mode, temperature control is not available.
■ Temperature unit switching
1. Press
until only the clock is displayed.
2. Press down
for more than 5 seconds.
The current temperature unit will be displayed. (Factory setting: °C)
to switch the temperature unit. (°C ⇔ °F)
3. Press
4. Press
to finish the setting.
If you do not press the button for 30 seconds, the displayed
temperature unit will be set.
5. AIRFLOW SETTINGS
5.1. Fan speed setting
Press
to control the fan speed.
)
)
The fan speed changes as follows.
(Auto)
(High)
When
is selected, the fan speed depends on the operating
condition.
To increase the air cleaning effect, set the fan speed to High.
5.2. Airflow direction setting
For details of the airflow ranges, refer to "Airflow direction
range".
■ Vertical airflow direction setting
Press
to adjust the vertical airflow direction.
)
)
■ Horizontal airflow direction setting
Press
to adjust the horizontal airflow direction.
)
)
■ Swing operation setting
Press
to select the Swing operation.
)
)
The Swing operation changes as follows.
Up/down
Left/right
NOTES: The Swing operation may stop temporarily when the indoor
unit fan is rotating at very low speed or is stopped.
DRY
FAN
HEAT
18.0 - 30.0 °C
16.0 - 30.0 °C
(Med)
(Low)
(Quiet)
Up/down/left/right
Stop swing