Fujitsu ABYA45LCT 설치 매뉴얼 - 페이지 16

{카테고리_이름} Fujitsu ABYA45LCT에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Fujitsu ABYA45LCT 16 페이지. Split type air conditioner ceiling type (50hz)
Fujitsu ABYA45LCT에 대해서도 마찬가지입니다: 서비스 매뉴얼 (33 페이지), 서비스 매뉴얼 (23 페이지)

페이지 인쇄

(3)

Remote controller setting

Turn on all of the indoor units.

Turn on the indoor unit with the unit number 0 last.

(Within 1 minute)

When the indoor units are turned on, error codes

01 and 31 will be displayed; however, these error

codes will be deleted by setting the remote controller.

Therefore, continue with the setting procedure.

Set the refrigerant circuit address. (Assign the same

number to all of the indoor units connected to an

outdoor unit.)

Refrigerant circuit

address

Set the "master" and "slave" settings. (Set the indoor

unit that is connected to the outdoor unit using a trans-

mission cable as the "master".)

Master

Slave

After completing the function settings, turn off all of the

indoor units, and then turn them back on.

If error code 01, 1F, 30, 31, or 32 is displayed, there

may be an incorrect setting. Perform the remote

controller setting again.

NOTE

When different indoor unit models are connected using the

group control system, some functions may no longer be avail-

able.

If the group control system contains multiple units that are

operated simultaneously, connect and set the units as shown

below.

Standard

pair

Outdoor

unit ①

Remote

Indoor

controller

unit

DIP switch setting

(Indoor unit)

Remote controller

setting

・

adress

・Master/Slave

: Transmission cable, Power supply cable

: Remote controller cable

*Make sure that the indoor unit with the unit number 0 is con-

nected to the outdoor unit using a transmission cable.

En-16

Function Number

Setting Value

00~15

Function Number

Setting Value

Simultaneous

twin

triple

Outdoor

unit ②

unit ③

Indoor

unit

: Power supply cable

: Bus wire

www.enindel.com

14. FRESH-AIR INTAKE

(1)

Open up the knockout hole for the fresh-air intake, as

shown in the figure. (If using half-concealed installation,

open up the top knockout hole instead.)

•

When removing the cabinet (iron plate), be careful not

to damage the indoor unit internal parts and surrounding

area (outer case).

•

When processing the cabinet (iron plate), be careful not

to injure yourself with burrs, etc.

(2)

Fasten the round flange (optional) to the fresh-air intake,

as shown in the figure. (If using half-concealed installation,

attach to the top.)

[After completing "3. INSTALLATION WORK"...]

(3)

Connect the duct to the round flange.

(4)

Seal with a band and vinyl tape, etc. so that air does not

leak from the connection.

Indoor

unit

15. CUSTOMER GUIDANCE

Explain the following to the customer in accordance with the

operating manual:

(1)

Starting and stopping method, operation switching, tem-

perature adjustment, timer, air flow switching, and other

remote control unit operations.

(2)

Air filter removal and cleaning, and how to use the air

louvers.

(3)

Give the operating and Installation Manuals to the cus-

tomer.

(4)

If the signal code is changed, explain to the customer how

it changed (the system returns to signal code A when the

batteries in the remote control unit are replaced).

*(4) is applicable to using wireless remote control.

For half concealed

installation

Indoor unit

CAUTION

Round duct (option parts)

Duct