Brother Airprint MFC-J485DW 빠른 설정 매뉴얼
{카테고리_이름} Brother Airprint MFC-J485DW에 대한 빠른 설정 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Brother Airprint MFC-J485DW 2 페이지.
Brother Airprint MFC-J485DW에 대해서도 마찬가지입니다: 사용자 설명서 (22 페이지), 제품 안전 매뉴얼 (21 페이지)
페이지 인쇄
MFC-J460DW / MFC-J480DW / MFC-J485DW
Quick Setup Guide
Read the Product Safety Guide first, then read this Quick Setup Guide for the
correct installation procedure.
Unpack the machine and check the components
1.
2.
Watch our FAQ Videos for help
with setting up your Brother
machine.
solutions.brother.com/videos
Starter Ink Cartridges [x4]
• Black
• Yellow
• Cyan
• Magenta
Visit the Brother support website
http://support.brother.com
1
Load plain Letter/A4 paper
Pull the paper tray completely
out of the machine.
Connect the telephone line cord
2
If you are not using your machine as a fax, go to
NOTE
If your machine is sharing one telephone line with an external telephone,
connect it as shown below. Before you connect the external telephone,
remove the white protective cap c from the EXT. jack of the machine.
Connect the telephone line cord.
Use the jack marked LINE.
4
Install starter ink cartridges
Follow the on-screen instructions to
Open the ink cartridge cover, and
install the ink cartridges.
then remove the orange protective
The machine will prepare the ink
part from the machine.
tube system for printing.
7
Choose the correct Receive Mode
If you are not using your machine as a fax, go to
The correct Receive Mode is determined
by the external devices and telephone
subscriber services (Voice Mail,
Distinctive Ring, etc.) you will be using on
the same line as the Brother machine.
For more information, see Receive Modes
in chapter 6 of the Basic User's Guide.
Remove the protective tape and film covering the machine and the LCD.
Make sure you have all components shown below.
Quick Setup Guide
Basic User's Guide
Product Safety Guide
1
Open the output paper tray
Fan the paper well and load it in the tray,
cover a.
and then adjust the paper guides.
3
1
2
3
a. Extension telephone
b. External telephone
c. Protective cap
5
When the machine has finished the initial cleaning
process, follow the on-screen instructions to
configure the machine settings.
• Check print quality
• Set date and time
• Set Firmware Update Notice
• Print the installation sheet
9
1.
Press Settings.
2.
Press a or b to select the following:
a.
Select [Fax]. Press OK.
b.
Select [Setup Receive]. Press OK.
c.
Select [Receive Mode]. Press OK.
d.
Press your preferred Receive Mode.
Press OK.
3.
Press Stop/Exit.
WARNING
WARNING indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injuries.
NOTE
NOTE specifies the operating environment, conditions for installation,
or special conditions of use.
Plastic bags are used in the packing of your machine. Plastic bags are not toys. To avoid
the danger of suffocation, keep these bags away from babies and children, and dispose
of them correctly.
NOTE
Manuals in Spanish for these models are available at
Manuales en Español para este modelo están disponibles en
• Most of the illustrations in this Quick Setup Guide show the MFC-J480DW.
• Save all packing materials and the box in case for any reason you must ship your
machine.
• You must purchase the correct interface cable for the interface you want to use
CD-ROM
(for a USB connection).
USB cable
We recommend using a USB 2.0 cable (Type A/B) that is no more than 6 feet
(2 meters) long.
Telephone Line Cord
Close the output paper tray cover, and
then slowly push the tray completely
into the machine.
3
Connect the power cord
Connect the power cord. The machine
will power on automatically.
Machine settings
8
Set your Station ID
If you are not using your machine as a fax, go to
Store your name and fax number so the
machine prints it on all outgoing fax pages.
For more information, see Enter Text on
Your Brother Machine in Appendix of the
Basic User's Guide.
WARNING
support.brother.com
NOTE
Pull out the paper support a, and unfold
the paper support flap b so that the
printed pages do not fall.
NOTE
You can adjust the control panel angle
to read the LCD more easily.
Choose your language
6
(if needed)
1.
Press Settings.
2.
Press a or b to select the following:
a.
Select [Initial Setup]. Press OK.
b.
Select [Local Language]. Press OK.
c.
Select your language. Press OK.
3.
Press Stop/Exit.
9
1.
Press Settings.
2.
Press a or b to select the following:
a.
Select [Initial Setup]. Press OK.
b.
Select [Station ID]. Press OK.
c.
Enter your fax number (up to 20 digits) using the dial pad,
and then press OK.
d.
Enter your name (up to 20 characters) using the dial pad,
and then press OK.
3.
Press Stop/Exit.
LEW787001-00
USA/CAN
Version 0
support.brother.com
2
1