Brother HL 2030 빠른 설정 매뉴얼 - 페이지 4
{카테고리_이름} Brother HL 2030에 대한 빠른 설정 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Brother HL 2030 30 페이지. Quick setup guide - english
Brother HL 2030에 대해서도 마찬가지입니다: 빠른 설정 매뉴얼 (18 페이지), 빠른 설정 매뉴얼 (30 페이지), 서비스 매뉴얼 (12 페이지)
페이지 인쇄
Regulations
Federal Communications Commission (FCC) Declaration of
Conformity (For USA)
Responsible Party:
Brother International Corporation
100 Somerset Corporate Boulevard
P.O. Box 6911
Bridgewater, NJ 08807-0911
USA
Telephone: (908) 704-1700
declares, that the products
Product name:
Laser Printer
Model number:
Laser Printer HL-2030, HL-2040 and HL-2070N
Model number:
HL-20
Product options:
ALL
complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
–
Reorient or relocate the receiving antenna.
–
Increase the separation between the equipment and receiver.
–
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
–
Consult the dealer or an experienced radio/TV technician for help.
Important
A shielded interface cable should be used in order to ensure compliance with
the limits for a Class B digital device.
Changes or modifications not expressly approved by Brother Industries, Ltd.
could void the user's authority to operate the equipment.
Industry Canada Compliance Statement (For Canada)
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada.
Radio interference (220-240 volt model only)
This printer follows EN55022 (CISPR Publication 22)/Class B.
Before you use this product, make sure that you use the following interface
cables.
1. A shielded parallel interface cable with twisted-pair conductors and that it
is marked "IEEE 1284 compliant".
2. A USB cable.
The cable must not be more than 2 meters long.
2
®
International E
S
Compliance Statement
NERGY
TAR
E
The purpose of the International
NERGY
the development and popularization of energy-efficient office equipments.
E
S
®
As an
NERGY
TAR
Partner, Brother Industries, Ltd. has determined
E
that this product meets the
NERGY
efficiency.
Laser Safety (100 to 120 volt Model Only)
This printer is certified as a Class 1 laser product under the U.S. Department
of Health and Human Services (DHHS) Radiation Performance Standard
according to the Radiation Control for Health and Safety Act of 1968. This
means that the printer does not produce hazardous laser radiation.
Since radiation emitted inside the printer is completely confined within
protective housings and external covers, the laser beam cannot escape from
the machine during any phase of user operation.
®
S
TAR
Program is to promote
S
®
TAR
guidelines for energy