LG 20M38D 소유자 매뉴얼 - 페이지 13

{카테고리_이름} LG 20M38D에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. LG 20M38D 45 페이지. Ips led monitor
LG 20M38D에 대해서도 마찬가지입니다: 소유자 매뉴얼 (42 페이지), 소유자 매뉴얼 (42 페이지), 소유자 매뉴얼 (42 페이지), 소유자 매뉴얼 (42 페이지), 소유자 매뉴얼 (42 페이지), 소유자 매뉴얼 (42 페이지), 소유자 매뉴얼 (45 페이지), 소유자 매뉴얼 (42 페이지), 소유자 매뉴얼 (42 페이지), 소유자 매뉴얼 (42 페이지)

LG 20M38D 소유자 매뉴얼
Mounting on a wall
For proper ventilation, allow a clearance of 10 cm
on each side and from the wall. Detailed
instructions are available from your dealer, see the
optional Tilt Wall Mounting Bracket Installation and
Setup Guide.
10 cm
If you intend to mount the Monitor set to a wall,
attach Wall mounting interface (optional parts) to
the back of the set.
When you install the Monitor set using a wall
mounting interface (optional parts), attach it
carefully so it will not drop.
1 If you use screw longer than standard, the moni-
tor might be damaged internally.
2 If you use improper screw, the product might be
damaged and drop from mounted position.
In this case, LG Electronics is not responsible
for it.
Model
16M38A
16M38I
Wall Mount (A
75 x 75
x B)
Standard
M4
screw
Number of
4
screws
Model
24M38A
24M38D
Wall Mount (A
100 x 100
x B)
Standard
M4
screw
Number of
4
screws
10 cm
10 cm
10 cm
19M38A
20M38A
22M38A
19M38D
20M38D
22M38D
20M38H
22M38H
27MP38VQ
24M38H
27MP38HQ
ASSEMBLING AND PREPARING
Wall Mount (A x B)
y
y
CAUTION
Disconnect the power cord first, and then
y
y
move or install the Monitor set. Otherwise
electric shock may occur.
If you install the Monitor set on a ceiling or
y
y
slanted wall, it may fall and result in severe
injury.
Use only an authorized LG wall mount
y
y
and contact the local dealer or qualified
personnel.
D o not over tighten the screws as this may
y
y
cause damage to the Monitor set and void
your warranty.
U se only screws and wall mounts that
y
y
meet the VESA standard. Any damages
or injuries by misuse or using an improper
accessory are not covered by the warranty.
Screw length from outer surface of back
y
y
cover should be under 8mm.
Wall mount Pad
Wall mount Pad
Back Cover
Standard screw
Max.8mm
NOTE
Use the screws that are listed on the VESA
y
y
standard screw specifications.
The wall mount kit will include an installation
y
y
manual and necessary parts.
The wall mount bracket is optional. You can
y
y
obtain additional accessories from your local
dealer.
The length of screws may differ depending
y
y
on the wall mount. Be sure to use the proper
length.
For more information, refer to the
y
y
instructions supplied with the wall mount.
13
Back Cover