Fujitsu Suelo AGY40-KV 운영 매뉴얼 - 페이지 9
{카테고리_이름} Fujitsu Suelo AGY40-KV에 대한 운영 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Fujitsu Suelo AGY40-KV 13 페이지.
Fujitsu Suelo AGY40-KV에 대해서도 마찬가지입니다: 운영 매뉴얼 (13 페이지)
페이지 인쇄
NOTES:
• This operation cannot be performed simultaneously with the Fan
mode, Dry mode, and Powerful operation.
• If the wired remote controller (optional) is connected, this function is
restricted.
8.3. 10 °C Heat operation
10 °C Heat operation maintains the room temperature at 10 °C so as to
prevent the room temperature to drop too low.
Press
to activate the 10 °C Heat operation.
The indoor unit will emit 1 short beep and [
indoor unit will turn on.
Press
to turn off the air conditioner.
[
] indicator will turn off.
NOTES:
• During the 10 °C Heat operation, only
• When the room temperature is warm enough, this operation will not
perform.
• If the wired remote controller (optional) is connected, this function is
restricted.
9. SETTINGS ON INSTALLATION
9.1. Remote controller custom code setting
By setting custom code of indoor unit and remote controller, you can
specify the air conditioner which the remote controller controls.
When two or more air conditioners are in the room and you wish to
operate them separately, set the custom code (4 selections possible).
NOTES: If custom codes is different between the indoor unit and the
remote controller, the indoor unit cannot receive a signal from
the remote controller.
How to set the remote controller custom code
1. Press
until only the clock is displayed on the remote
controller display.
2. Press and hold
for more than
5 seconds.
The current custom code will be
displayed (initially set to A).
3. Press
to change the
custom code between A↔B↔C↔D
(
).
* Match the custom code on the display
to the air conditioner custom code.
4. Press
again.
The custom code will be set.
The display will return to the clock display.
• To change the air conditioner custom code, contact an authorized
service personnel (initially set to A).
• If you do not press any buttons for 30 seconds after the custom
code is displayed, the display returns to the clock display. In this
case, repeat the setting from step 2.
• Depending on the remote controller, the custom code may return
to A when replacing the batteries. In this case, reset the custom
code as necessary. If you do not know the air conditioner custom
code, try each code until you fi nd the code which operates the air
conditioner.
10. CLEANING AND CARE
] indicator on the
Indicator Lamp
TIMER
OPERATION
ECONOMY
The frequency of the cleaning is as shown in the following table.
: Lighting
: OFF
Cleaning indoor unit body
Cleaning air fi lter
is valid.
Cleaning Ion deodorization fi lter
Replacing Apple-catechin fi lter
(Model name: UTR-FA16)
Replacing Ion deodorization fi lter
(Model name: UTR-FA16-2)
* The air cleaning fi lters are sold separately. When you replace them,
please contact the store of purchase.
Cleaning indoor unit body
NOTES:
• Do not use water hotter than 40 °C.
• Do not use scouring cleanser, volatile solvents such as benzene or
thinner.
1. Wipe the indoor unit body gently with a soft cloth moisten
with warm water.
2. Wipe the indoor unit body gently with a dry and soft cloth.
Cleaning air fi lter
1.
Remove the Intake Grille.
CAUTION
• Before cleaning this product, be sure to turn it off and
disconnect all the power supply.
• Before starting operation, make sure that the intake
grille has been shut completely. Incomplete closing
of the intake grille might have an effect on the proper
working or performance of the air conditioner.
• If the fi lter cleaning involves high-place work, please
consult the authorized service personnel.
• Do not touch the aluminum fi ns of heat exchanger
built-in the indoor unit to avoid personal injury when
you maintain the unit.
• Do not expose the indoor unit to liquid insecticides or
hair sprays.
• Do not stand on slippery, uneven or unstable surfaces
when you maintain the unit.
What to do
Indoor unit body
Intake grille
Rope
Frequency
When you notice
Every 2 weeks
Every 3 months
Every 3 years
Air fi lters
En-8