Fujitsu LifeBook B2630 바이오스 매뉴얼 - 페이지 2

{카테고리_이름} Fujitsu LifeBook B2630에 대한 바이오스 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Fujitsu LifeBook B2630 32 페이지. Lifebook b series
Fujitsu LifeBook B2630에 대해서도 마찬가지입니다: 바이오스 매뉴얼 (38 페이지)

페이지 인쇄

L i f e B o o k B S e r i e s N o t e b o o k B I O S

B Series BIOS

BIOS SETUP UTILITY

The BIOS Setup Utility is a program that sets up the

operating environment for your notebook. Your BIOS

is set at the factory for normal operating conditions,

therefore there is normally no need to set or change the

BIOS environment to operate your notebook.

The BIOS Setup Utility configures:

• Device control feature parameters, such as changing

I/O addresses and boot devices.

• System Data Security feature parameters, such

as passwords.

Entering the BIOS Setup Utility

To enter the BIOS Setup Utility do the following:

1. Turn on or restart your notebook.

2. Press the [

] key once the Fujitsu logo appears

on the screen. This will open the main menu

of the BIOS Setup Utility with the current

settings displayed.

3. Press the arrow keys to scroll through the other

setup menus to review or alter the current settings.

Navigating Through The Setup Utility

The BIOS setup utility consists of six menus; Main,

Advanced, Security, Boot, Info and Exit. This document

explains each menu, including all submenus and setup

items.

The following procedures allow you to navigate the setup

utility menus:

1. To select a menu, use the cursor keys: [

2. To select a field within a menu or a submenu, use the

cursor keys: [ ], [

3. To select the different values for each field, press the

[

] or [

] to change to the next higher selec-

Spacebar

tion and [

] or [-] to go to the next lower selection.

4. To activate a submenu press the [Enter] key.

5. To return to a menu from a submenu, press

the [

] key.

Esc

6. To go to the Exit menu from any other menu,

press the [

] key.

Esc

],[

P O I N T S

• Selecting a field causes a help message about the field

to be displayed on the right-hand side of the screen.

• Pressing the Enter key with the highlight on a selec-

tion that is not a submenu or auto selection will cause

a list of all options for that item to be displayed.

Pressing the Enter key again will select the high-

lighted choice.

7. Pressing the [

the default values.

8. Pressing the [

tion and exits the BIOS Setup Utility. You will be

asked to verify this selection before it is executed.

9. Pressing the [

Entering the Setup Utility After a Configuration

Change or System Failure

If there has been a change in the system configuration

that does not match the parameter settings stored

in your BIOS memory, or there is a failure in the system,

the system beeps and/or displays an error message after

the Power On Self Test (POST). If the failure is not

too severe, it will give you the opportunity to modify

the settings of the setup utility, as described in the

following steps:

1. When you turn on or restart the computer there is

a beep and/or the following message appears on

the screen:

Error message - please run SETUP

program Press <F1> key to continue,

<F2> to run SETUP

2. If an error message is displayed on the screen, and

you want to continue with the boot process and start

the operating system anyway, press the [

P O I N T S

• If your notebook emits a series of beeps that sounds

like a code and the display is blank, refer to the Trou-

bleshooting Section of your system User's Guide. The

Troubleshooting Section includes a list of error mes-

sages and their meanings.

• If your data security settings require it, you may be

asked for a password before the operating system will

be loaded.

] key resets all items in the BIOS to

] key saves the current configura-

F10

] key gives you a general help screen.

] key.