2N EasyGate 빠른 시작 - 페이지 2

{카테고리_이름} 2N EasyGate에 대한 빠른 시작을 온라인으로 검색하거나 PDF를 다운로드하세요. 2N EasyGate 2 페이지.

페이지 인쇄

EasyGate QuickStart

Read the CD-ROM User Manual carefully to get familiar with all system functions.

Security Precautions

• Do not switch on EasyGate in the vicinity of medical

apparatuses to avoid interference. The minimum distance

of the antenna and pacemakers should be 0.5 m.

• Do not switch on EasyGate aboard a plane.

• Do not switch on EasyGate near petrol stations, chemical

facilities or sites where explosives are used.

• Any mobile telephone use prohibition based on RF energy

radiation applies to EasyGate too.

• EasyGate may disturb the function of TV sets, radio sets

and PCs.

• Warning! EasyGate contains components that can be

swallowed by small children (SIM card, antenna, etc.).

• The voltage value mentioned on the adapter may not be

exceeded. If you connect EasyGate to another power

supply, make sure that the voltage value lies in the

acceptable range.

• When your EasyGate comes to the end of its operational

life, dispose of it in accordance with applicable regulations.

Basic Functions

• The primary purpose of EasyGate is to

transmit voice between a GSM network

and an attached FXO-interface terminal.

• You can

establish

data connections

(GPRS, CSD) and send/receive SMS in

combination with a PC.

• You can send an SMS to a pre-

programmed number using the SMS

sending input.

• Models of EasyGate with fax converter

can

transmit

fax

messages

using

analog fax Group 3 or data using

analog modem on telephone line.

External Antenna Connection

Screw the antenna enclosed into the

SMA antenna connector. Tighten the

antenna connector gently with your

hand, never use wrenches!

SIM Card Installation

Take off the SIM card holder on

EasyGate's back side, insert the SIM

card and replace the holder fixing the

safety pin. Select the required GSM

provider and SIM card services, such

call

forwarding,

call

barring,

preferred networks, SMS centre, etc.

using your mobile phone before

inserting your SIM card in EasyGate.

An EasyGate delivery contains the

following:

EasyGate

Antenna

Supply adapter

Telephone cable

PC-connection serial cable

SMS sending input

connector

Dowels

Screws

User Manual on a CD-ROM

QuickStart manual +

mounting pattern

Sotware CD-ROM

Warranty certificate

Proper Location

• EasyGate is designed for vertical mounting on

suspension holes (use the mounting pattern). This

position is the best for GSM signal reception.

• Install EasyGate with respect to a good GSM signal

strength.

• Place EasyGate out of range of sensitive devices and

human bodies for electromagnetic interference reasons.

• EasyGate is designed for indoor use. Do not place it

near heat sources and on sites exposed to direct solar

radiation. It may not be exposed to rain, flowing water

and moisture. In addition, it may not be exposed to

aggressive gas, acid vapours, solvents, etc.

Telephone Line Connection

EasyGate can be connected to any FXO-interface

equipment (standard telephone set, answering machine,

PBX CO line,...). EasyGate is equipped with identification of

calling party (CLIP) via FSK and so it is advantageous to

connect a terminal that is able to display the CLI.

Power Supply Connection

EasyGate is fed with 10-16V DC voltage. Where a source

other than the included supply adapter is used, the voltage

range and polarity shown on the EasyGate supply connector

have to be maintained.

Do not activate the power supply until the antenna is

connected to EasyGate to avoid the GSM module damage.

SIM Card PIN protection

1. Hook off the telephone, you can hear the PIN

tone:

2. Enter the PIN using the DTMF and press a

1 pc

for confirmation. To cancel a wrong PIN

1 pc

hang up the telephone line.

3. If you hear the busy tone in a while (a few

1 pc

seconds),

you

1 pc

correctly.

The

1 pc

automatically upon the next power up.

1 pc

4. If you hear the PIN tone again in a while, you

have entered a wrong PIN. Re-enter the PIN.

2 pcs

5. If you hear the PUK tone in a while, you have

2 pcs

entered a wrong PIN and the SIM card is

1 pc

blocked. Use the mobile phone to unblock

the SIM card.

1 pc

Outgoing Call

1. Suppose that the SIM card has been

1 pc

inserted, the PIN entered or not required,

and EasyGate registered to GSM network –

the GSM Network LED is permanently on.

2. Hook off the telephone, you can hear the

dialtone and the Line LED starts flashing.

3. Dial the GSM subscriber number. EasyGate

receives tone dialling (DTMF) by default. If

your telephone transmits pulse dialling only,

program EasyGate to receive pulse dialling.

When you make a delay in your dialling

longer than 5s (programmable), the connection

is established.

4. If the called subscriber is available, you can

hear the ringing tone. If not, you can hear the

busy tone or any of the GSM provider's

messages.

5. When the called subscriber answers the call,

a call is established. The Line LED is

permanently on during the call.

6. Hang up to terminate the call. The Line LED goes

off. If the called subscriber is the first to hang up,

you can hear the busy tone and hang up.

Incoming Call

1. An incoming call is signalled by ringing. The

Line LED flashes during ringing.

2. Hook off the phone to establish the call. The

Line LED is permanently on during the call.

3. For call termination see the Outgoing Call

section.

EC Declaration of Conformity

Hereby, 2N TELEKOMUNIKACE a.s., declares that the product 2N EasyGate is in compliance with the essential

requirements and other relevant provisions of Directive 1999/5/EC. Declaration of conformity you can find on

CD-ROM or on our website www.2n.cz.

Analogue FAX and Data Connection (optional)

EasyGate with fax converter has ability to

manage fax messages using analogue fax

Group 3 and data connection using analog

modem connected to telephone line. The fax or

data service must be registered with your GSM

operator.

have

entered

the

Outgoing FAX Call and Data Connection

will

entered

Before destination number dial code *01* for fax

call or *02* for data connection.

Incoming FAX Call and Data Connection

It is recommended to activate separate fax

number on your SIM card –multinumbering

scheme. Fax messages and data connection

should be routed to apprppriate number.

If the fax or data number is not activated, the call

from analogue network is not detected as fax or

data call and is routed via the analogue channel

of GSM network, the connection can´t be

established. In this case it is possible to set fax

engine in the gateway to receive the next call as

fax or data call. It is possible to make this setting

permanent - see the manual on CD. This function

is not guaranteed by all operators.

Indication LEDs

• Light is on whenever EasyGate is

Power

supply

• light = registered to GSM

• flashes once in 1s = not registered,

• flashes once in 3s = not registered,

GSM

network

• flashes 4 times quickly = enter your

• flashes 8 times quickly = enter your

• no light = standby

• flashes quickly = line off-hook or

• light = call

• flashes once in 3s = data connection

telephone

line

On FAX models:

• Flashes 2 times then pause = fax

on.

SIM card inserted

SIM card not inserted

PUK

ringing

in progress

connection in progress; after power

on signalize need of FW upgrade