Brother P-touch H107 사용자 설명서
{카테고리_이름} Brother P-touch H107에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Brother P-touch H107 2 페이지.
Brother P-touch H107에 대해서도 마찬가지입니다: 사용자 설명서 (2 페이지)
페이지 인쇄
User's Guide
English
With your P-touch H107/H108, you can create labels for multiple
applications. Select from the many frames, character sizes and
styles to design beautiful custom labels. In addition, the variety of
tape cassette available allows you to print labels with different widths
and exciting colours.
Read this manual carefully before you begin and keep the manual in
a handy place for future reference.
Power Supply and Tape Cassette
Cassette
1
cover
Tape cutter
lever
Open the cassette cover by pressing the
above indicated area at the top end of the
P-touch.
If a tape cassette is already installed, remove it by
pulling it straight up. Also, if batteries are already
installed, remove them.
• Make sure that the power is turned off when
replacing batteries or tape cassettes.
LCD Display & Keyboard
1
2
3
4
9
10
11
12
13
14
15
16
17
Troubleshooting
Error message
Message
Cause/Remedy
The batteries are weak.
If using AAA alkaline batteries: Replace them with new
Low Battery!
ones.
If using Ni-MH batteries: Charge them fully.
Battery Dead
The installed batteries have expired.
An invalid number was entered as the label length.
Invalid!
(This is not displayed in Auto Designs).
• You tried to print a text file when there is no data
stored in the memory.
•
is pressed when no text is entered.
No Text!
• You tried to select Text Preview or Cable Label when
no text is entered.
•
was pressed when no text was entered while
using the DECO MODE or Auto Designs.
• You tried to enter a 3rd line by pressing
Line Limit!
• You tried to print or preview two lines of text while
3.5mm or 6 mm tape is installed. Install tape of a
larger size.
You tried to print a label when there is no cassette
No Cassette!
installed.
The tape cutter lever was used during the printing
Cutter Error
process.
Safety Precautions
Indicates a potentially hazardous
WARNING
situation which, if not avoided,
could result in death or serious
injuries.
Follow these guidelines to avoid the risk of fire, burns, injury,
electric shocks, rupture, overheating, abnormal odours or
smoke.
• Do not touch the P-touch during a lightning storm.
• Do not use the P-touch in places of high humidity (such as bathrooms).
• Do not overload the power cord.
• Do not allow the P-touch batteries to get wet, for example, by handling them with
wet hands or spilling beverages onto them.
• Since loss of eyesight may result when leaked fluid from batteries gets into your
eyes, immediately rinse your eyes with a large amount of clean water, and then
seek medical attention.
• Do not disassemble or modify the P-touch batteries.
• Do not allow a metal object to contact both the plus and minus ends of a battery.
• Do not use sharp objects, such as tweezers or a metallic pen, to change the
batteries.
• Do not throw the batteries into fire or expose to heat.
• Remove batteries immediately and stop using the P-touch if you notice abnormal
odour, heat, discolouration, deformation or anything unusual while using or storing
it.
• Do not use a damaged or leaking battery as the fluid may get on your hands.
• Do not use a deformed or leaking battery or one with a damaged label. There is a
possibility of generating heat.
Ver. 0
2
Insert six new AAA alkaline batteries
(LR03) or fully charged Ni-MH batteries
(HR03), making sure that their poles
point in the correct directions.
Users of alkaline batteries:
Always replace all six batteries at the
same time with brand new ones.
Users of Ni-MH batteries:
Always replace all six batteries at the
same time with fully charged ones.
NOTE
Visit us at http://support.brother.com/ for the latest
information about the recommended batteries.
1.
Size
14. Style key
2.
Cursor
15. Character keys
3.
Caps
16. Caps key
4.
Underline/Frame
17. Symbol key
5
5.
Width
18. Menu key
6
6.
Style
19. Clear key
7.
Label Length
20. Print key
7
8
If a specific label length has been
21. Enter key
18
selected,
also appears.
22. Auto Designs function key
19
8.
Guidance (left, right)
23. Frame key
20
9.
Power key
24. Accent key
10. Cursor key : Right
25. Space key
11. Cursor key : Left
21
22
12. Backspace key
23
13. Size key
NOTE
• The LCD shows one row of 12 characters; however, the text that
you enter can be up to 80 characters in length.
• While selecting the settings, press the Space key to go back to
the default item.
• The print preview is a generated image of the label, and may
differ from the actual label when printed.
24
• Label length shown on LCD may slightly differ from the actual
25
label length when printed.
Message
Cause/Remedy
The maximum number of characters (80 characters for
Text Full!
regular text, 50 characters for Auto Designs and DECO
MODE) have already been entered.
With the DECO MODE function:
Since the number of entered characters exceeds the
label length, reduce the text.
Text Limit!
All other functions:
Since the number of entered characters exceeds the
label length, reduce the text or select [Auto] as the label
length.
Printing on 3.5mm tape with invalid Frame setting ON.
No Frame OK?
(Select
to print with no Frame,
cancel).
Feeding tape after printing when [Chain Print] is
OK to Feed?
selected. Refer to "Setting Margin".
Only 12mm tapes are available for use with DECO
Insert 12mm
MODE function.
.
Wrong Tape!
Use a tape cassette with the
CAUTION
Follow these guidelines to avoid personal injury, liquid
leakage, burns or heat.
• When the P-touch is not being used, store it out of the reach of children. In addition,
do not allow children to put P-touch parts or labels in their mouths. If any object has
been swallowed, seek medical attention.
• Do not touch metal parts near the print head immediately after printing.
• Do not touch the cutter blade.
• If leaked fluid from batteries gets onto your skin or clothes, immediately rinse them
with clean water.
• Remove the batteries if you do not intend to use the P-touch.
• Do not use a battery other than that specified. Do not use combinations of old and
new batteries or combinations of different types, different charging levels, different
manufacturers or different models. Do not insert a battery with its plus and minus
ends reversed.
• Do not drop or hit the P-touch.
• Do not press on the LCD display.
• Do not put your finger inside the P-touch when you close the cassette cover.
• Before using Ni-MH rechargeable batteries, carefully read the instructions for the
batteries and battery charger, and be sure to use them correctly.
• When using Ni-MH rechargeable batteries, charge the batteries with a specialized
battery charger before using the batteries.
General Precautions
• Depending on the location, material, and environmental conditions, the label may
unpeel or become irremovable, the colour of the label may change or be
transferred to other objects. Before applying the label, check the environmental
conditions and the material.
• Do not use the P-touch in any way or for any purpose not described in this guide.
Doing so may result in accidents or damage to the P-touch.
• Use only Brother TZe tapes with the P-touch. Do not use tapes that do not have
the
mark.
• Only use a soft, dry cloth to clean the P-touch; never use alcohol or other organic
solvents.
• Use a soft wipe to clean the print head; never touch the print head directly.
• Do not put any foreign objects into any part of the P-touch.
3
Print head
End of tape
Toothed
wheel
Tape guide
Insert a tape cassette, making sure that
it snaps into place.
• Make sure that the end of the tape feeds under
the tape guides.
• Use only Brother TZe tapes with P-touch.
Specifications
Dimensions:
Approx. 110(W) × 208(D) × 59(H)mm
(W x D x H)
Weight:
Approx. 390 g
(without batteries and tape cassette)
Power supply:
Six AAA alkaline batteries (LR03)
Six AAA Ni-MH batteries (HR03)*
Tape cassette:
Brother TZe tape (width)
3.5mm, 6mm, 9mm, 12mm
1
*
Visit us at http://support.brother.com/ for the latest information
about the recommended batteries.
What to do when...
Problem
The display stays blank
• Check that the batteries are correctly
after you have turned on
inserted.
the P-touch.
• If the batteries are weak, replace them.
When the label is printed
• See "Setting Margin" in this users guide
out, the margin(space) is
and select [Half] or [Narrow] to have
too large on both sides of
smaller margins for your label.
the text.
• Check that the tape cassette has been
The P-touch does not
inserted correctly.
print, or the printed
• If the tape cassette is empty, replace it.
to
characters are not formed
• Check the cassette cover is properly
properly.
closed.
• If the batteries are weak, replace them.
• When power is disconnected for more
The setting has cleared
than three minutes, all text & formats in
on its own.
the display will be lost. Language and Unit
settings will also be cleared.
mark.
• There may be some dust on the print
head. Remove the tape cassette and use
A blank horizontal line
a dry cotton swab to gently wipe the print
appears through the
head with an up-and-down motion.
printed label.
• The print head can be cleaned more
easily if the optional print head cleaning
cassette (TZe-CL3) is used.
• Do not place the P-touch, batteries in direct sunlight or rain, near heaters or other
Indicates a potentially hazardous
appliances, or in any location exposed to extremely high or low temperatures (e.g.
situation which, if not avoided,
on the dashboard or in the back of your car). Avoid high humidity or dusty
may result in minor or moderate
locations.
injuries.
• Do not apply excessive pressure to the cutter lever.
• Do not try to print if the cassette is empty; it will damage the print head.
• Do not pull the tape while printing or feeding; it will damage the tape and P-touch.
• Any data stored in memory will be lost due to failure or repair of the P-touch, or if
the battery expires.
• The P-touch is not equipped with a charging feature for rechargeable batteries.
• The length of the printed label may differ from the displayed label length.
• A protective clear plastic sticker is placed over the display during manufacturing
and shipping. This sticker should be removed prior to use.
• When power is disconnected for more than three minutes, all text, format settings
and any text files stored in the memory will be cleared.
We,
Brother Industries, Ltd.
15-1, Naeshiro-cho, Mizuho-ku,
Nagoya 467-8561 Japan
declare that this product is in conformity with the essential requirements of all relevant directives
and regulations applied within the European Community.
The Declaration of Conformity (DoC) can be downloaded from the Brother Solutions Center.
Visit support.brother.com/ and:
•
select "Manuals"
•
select your model
•
select "Declaration of Conformity"
•
click "Download"
Your Declaration will be downloaded as a PDF file.
4
Cutter's
edge
Tape
exit slot
Securely close the cassette cover, making
sure that it snaps into place.
Initial Settings
1
Start your P-touch.
Supply power by using six AAA batteries, and then press
2
Set the language.
1
[English/Español/Français/Hrvatski/Italiano/Magyar/
Nederlands/Norsk/Polski/Português/Portug. (BR)/
Română/Slovenski/Slovenský/Suomi/Svenska/Türkçe/
Čeština/Dansk/Deutsch]
3
Set the unit of measurement.
The default setting is [mm].
NOTE
• The P-touch automatically turns off if no keys are pressed within
five minutes.
• To cancel any operation, press
Problem
Solution
The P-touch has "locked
up" (i.e., nothing happens
when a key is pressed,
even though the P-touch
is on).
The power turns off when
you try to print.
The tape does not feed
properly or the tape gets
stuck inside the P-touch.
All text and format settings
need to be cleared to
create a new label.
The LCD is set to an
incorrect language.
Contact may differ by country.
See the Website at http://www.brother.eu/
Declaration of Conformity
(Europe/Turkey Only)
.
/
[Language]
/
.
/
[Unit]
/
[inch/mm]
.
.
Solution
• Refer to "Resetting the P-touch".
• The batteries may be weak. Replace
them.
• Check that the batteries are correctly
inserted.
• If the batteries are weak, replace them.
• Check that the end of the tape feeds
under the tape guides.
• The cutter lever is used while printing. Do
not touch the cutter lever during printing.
• Press
and select [Text&Format].
• Refer to "Initial Settings".
Contact Information