Brother P-touch LW1704001 사용자 설명서

{카테고리_이름} Brother P-touch LW1704001에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Brother P-touch LW1704001 2 페이지. Brother electronic labeling system user's guide

페이지 인쇄

USER'S GUIDE

www.brother.com

INTRODUCTION

With your PT-1880, you can create labels for any application. Select from the

many frames, character sizes and styles to design beautiful custom labels. In

addition, the variety of tape cartridges available allows you to print labels with

different widths and exciting colours.

Read this User's Guide carefully before starting and keep the User's Guide in

a handy place for future reference.

GENERAL PRECAUTIONS

• Use only Brother TZ tapes with this machine. Do not use tapes that do not have

the

mark.

• Do not disassemble or modify the machine/AC adapter.

• Do not clean the machine with alcohol or other organic solvents. Only use a soft, dry

cloth.

• Do not touch the print head mechanism. Use a soft wipe (e.g. a cotton swab) when

cleaning the print head.

• To avoid injuries, do not touch the cutter's edge.

• To prevent damage or breakage, do not press on the LCD display.

• Do not put any foreign objects into or heavy objects on the machine.

• Do not leave any rubber or vinyl on the machine for an extended period of time,

otherwise the machine may be stained.

• Do not get the machine/AC adapter/power plug wet, such as by handling them with

wet hands or spilling beverages on to them.

• Do not expose the machine/AC adapter to extremely high temperatures or high

humidity. Never leave them on the dashboard or in the back of your car, near heaters

or other hot appliances. Keep them out of both direct sunlight and rain.

• Avoid using the machine in extremely dusty places.

• Depending on the environmental conditions and the applied settings, some

characters or symbols may be difficult to read.

• Do not pull on the tape being fed from the P-touch labeler, otherwise the tape

cassette or P-touch labeler may be damaged.

• Do not attempt to cut the tape while printing or feeding since this will damage the tape.

• Do not try to print labels using an empty tape cassette set in the P-touch labeler. Doing

so will damage the print head.

• Remove the batteries and disconnect the AC adapter if you do not intend to use the

machine for an extended period of time. (Note: When power is disconnected for more

than five minutes, all text, format settings and any text files stored in the memory will

be cleared.)

• Do not use old and new batteries together or mix alkaline batteries with other type

batteries, or set the positive and negative end in the wrong position. Otherwise, the

batteries may leak or be damaged.

• Do not use metallic articles, such as tweezers or metallic pen, when exchanging the

batteries.

• Always use the specified voltage and the suggested AC adapter (AD5000) for

this machine to prevent any damage or failure.

• To prevent fire or electric shock, make sure that the plug of the AC adapter is fully

inserted into the power outlet. Do not use an outlet that is loose.

PREPARATION

Unpacking Your P-touch Labeler

Check that the package contains the following before using your P-touch la-

English

beler.

PT-1880

Printed in China

LW1704001

TZ tape cassette

Included items may differ by distribution.

Power Supply

Make sure that the power is turned off when replacing batteries.

Turn the machine over and remove the battery compartment cover.

If batteries are already installed, remove them.

Insert six new AA-size alkaline

batteries (LR6), making sure that

their poles point in the correct

directions. Always replace all six

batteries at the same time using

brand new ones.

Attach the battery compartment cover by inserting the three hooks at the

bottom into the slots on the machine, then pushing down firmly on the

cover until it snaps into place.

When using optional AC adapter (model

AD5000)

Insert the plug on the adapter cord into

the adapter jack on the right side of the

machine.

Insert the plug into the nearest standard

electrical outlet.

For memory back up, we recommend using

AA-size alkaline batteries (LR6) together

when using the AC adapter.

Tape Cassettes

Make sure that the power is turned off when replacing a tape cassette.

Open the tape compartment cover by lifting up both sides at the same time.

If a tape cassette is already installed, remove it by pulling it straight up.

Insert a tape cassette, making sure that it snaps into place.

End of tape

Toothed Wheel

Tape guide

• Make sure that the end of the tape feeds under the tape guides.

• If the ink ribbon is loose, use your finger to wind the toothed wheel in the

direction of the arrow on the cassette.

After you have installed the tape, feed the tape (

push in the tape cutter lever to cut the tape.

Securely close the front cover, making sure that it snaps into place.

OPERATION

Keyboard & LCD

Size

Cursor

User's Guide

Caps

Accessories Guide

Tape cutter lever

Warranty Card

Print key

Preview key

Font keys

Character keys

Battery compartment

cover

Tab key

Caps key

Shift key

Symbol key

Auto Format key

• The LCD shows one row of 15 characters; however, the text that

you enter can be up to 80 characters in length, which will scroll

across the display.

• Use

with Shift key to go to beginning/end of the text.

Turning the Power On

Setting Language (

[Language]

Setting unit

(mm/inch)

[Unit]

• The machine automatically turns off if no key is pressed within 5

minutes.

• To cancel operations, press

Tape compartment

• To initialize the P-touch labeler back to factory settings, turn off the

cover

machine and then while holding down

turn the machine back on. Finally, release

) once and then

[GETTING STARTED]

REFERENCE

Troubleshooting

Error message

Message

Width

Battery Weak!

Check Battery!

Invalid!

Style

Underline/Frame

Label Length

No Text!

Line Limit!

No Cassette!

Cutter Error!

Full!

Text Too Long!

Esc key

OK key

Cursor keys

No Frame OK?

Power key

Function key

Backspace key

What to do when...

Enter key

Problem

The display stays blank

Shift key

after you have turned on

Accent key

the machine.

Space key

When the label is

printed out, there is too

much margin (space) on

both sides of the text.

The machine does not

print, or the printed

characters are not

formed properly.

The setting has cleared

on its own.

A blank horizontal line

appears through the

printed label.

The machine has

"locked up" (i.e., nothing

happens when a key is

English/Spanish/

)

(

)

pressed, even though

French/Portuguese

the machine is on.)

[English]

The power turns off

when you try to print.

The tape does not feed

properly or the tape gets

(

)

stuck inside the machine.

All text and format settings

need to be cleared to

[mm]

create a new label.

Specifications

Item

Dimensions

Weight

and

, press

Power supply

and

Tape cassette

Accessories

Tape Cassettes

AC Adapter

Carrying Case

Cause/Remedy

The batteries are weak. Replace them with new ones.

The installed batteries are about to run out.

• There is no text above the cursor when you set Number-

ing.

• Invalid character is selected for Numbering.

• Invalid number is selected for Tab Length or Label Length.

• You tried to print a text file when there is no data stored in

the memory.

• The Print key is pressed when no text is entered.

• You tried to set Copies, Numbering or Mirror when no text

is entered.

• You tried to enter a 3rd line by pressing Enter key.

• You tried to print a 2 line text when 3.5 mm or 6 mm tape is

installed.

You tried to print a label when there is no cassette installed.

Tape cutter lever is used in the middle of printing process.

The maximum number of characters (80 characters) have

already been entered.

The text length exceeds the selected label length or the

selected Auto Format setting length.

Printing on 3.5 mm tape with invalid Frame setting ON.

(Select

to print with no Frame,

to cancel.)

Solution

• Check that the batteries are correctly inserted.

• If the batteries are weak, replace them.

• Check that the AC adapter is correctly connected.

• Refer to "Setting [Margin] (Tape Margin)" on this users

guide and select [Half] or [Narrow] to have smaller margins

for your label.

• Check that the tape cassette has been inserted correctly.

• If the tape cassette is empty, replace it.

• Check the tape compartment cover is properly closed.

• The batteries may be weak. Replace them.

• When power is disconnected for more than five minutes, all

text & formats in the display will be lost. Language and unit

settings will also be cleared.

• There maybe some dust on the print head. Remove the

tape cassette and use a dry cotton swab to gently wipe the

print head with and up-and-down motion.

• The print head can be cleaned more easily if the optional

print head cleaning cassette (TZ-CL4) is used.

• Turn off the machine, and then while holding

down

and

, press

to turn the machine back

on. Finally, release

and

• Note: The text and formats in the display are erased. Also,

the language and unit settings will be cleared.

• The batteries may be weak. Replace them.

• Check that the batteries are correctly inserted.

• Check that the end of the tape feeds under the tape guides.

• The cutter lever is used while printing. Do not touch the

cutter lever during printing.

• Press

while holding down

, and select [Text&For-

mat].

Specification

167 mm (W) × 215 mm (D) × 57 mm (H)

570 g (without batteries and tape cassette)

Six AA-size alkaline batteries (LR6) or optional AC adapter

(model AD5000)

Brother TZ tape (width) :

3.5 mm, 6 mm, 9 mm, 12 mm, 18 mm

(Supplies may differ by distribution.)

Stock No.

See the attached "Supplies and Accessories Guide".

model AD5000

CC3500