Fujitsu LifeBook N3430 바이오스 매뉴얼 - 페이지 2

{카테고리_이름} Fujitsu LifeBook N3430에 대한 바이오스 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Fujitsu LifeBook N3430 23 페이지. Lifebook n series

페이지 인쇄

L i f e B o o k N S e r i e s N o t e b o o k B I O S

N Series BIOS

BIOS SETUP UTILITY

The BIOS Setup Utility is a program that sets up the

operating environment for your notebook. Your BIOS

is set at the factory for normal operating conditions,

therefore there is no need to set or change the BIOS

environment to operate your notebook.

The BIOS Setup Utility configures:

Device control feature parameters, such as changing

■

I/O addresses and boot devices.

System Data Security feature parameters, such

■

as passwords.

Entering the BIOS Setup Utility

To enter the BIOS Setup Utility do the following:

1. Turn on or restart your notebook.

2. Press the [F2] key once the Fujitsu logo appears on

the screen. This will open the main menu of the

BIOS Setup Utility with the current settings

displayed.

3. Press the arrow keys to scroll through the other

setup menus to review or alter the current settings.

Navigating Through The Setup Utility

The BIOS setup utility consists of six menus: Informa-

tion, Main, Advanced, Security, Boot, and Exit. This

document explains each menu in turn, including all

submenus and setup items.

The following procedures allow you to navigate the

setup utility menus:

1. To select a menu, use the cursor keys:

2. To select a field within a menu or a submenu, use the

cursor keys:

[ ], [ ].

3. To select the different values for each field, press the

[Spacebar] or [+] to change to the next higher

selection and [F5] or [-] to go to the next lower

selection.

4. To activate a submenu press the [Enter] key.

5. To return to a menu from a submenu, press

the [Esc] key.

6. To go to the Exit menu from any other menu,

press the [Esc] key

7. Pressing the [F9] key resets all items in the BIOS to

the default values.

8. Pressing the [F10] key saves the current configura-

tion and exits the BIOS Setup Utility. You will be

asked to verify this selection before it is executed.

9. Pressing the [F1] key gives you a general help screen.

Entering the Setup Utility After a Configuration

Change or System Failure

If there has been a change in the system configuration

that does not agree with the parameter settings stored

in your BIOS memory, or there is a failure in the system,

the system beeps and/or displays an error message after

the Power On Self Test (POST). If the failure is not

too severe, it will give you the opportunity to modify

the settings of the setup utility, as described in the

following steps:

1. When you turn on or restart the computer there is a

beep and/or the following message appears on the

screen:

Error message - please run SETUP

program Press <F1> key to continue,

<F2> to run SETUP

2. If an error message is displayed on the screen, and

[

], [

you want to continue with the boot process and start

the operating system anyway, press the [F1] key.

■

Selecting a field causes a help message

about that field to be displayed on the

right-hand side of the screen.

Pressing the Enter key with the highlight

■

on a selection that is not a submenu or

auto selection will cause a list of all

options for that item to be displayed.

Pressing the Enter key again will select

the highlighted choice.

■

If your notebook emits a series of beeps

that sounds like a code and the display is

blank, refer to the Troubleshooting sec-

tion of your system User's Guide. The

Troubleshooting Section includes a list of

error messages and their meanings.

If your data security settings require it,

■

you may be asked for a password before

the operating system will be opened.