Brother PT1100SB 사용자 설명서
{카테고리_이름} Brother PT1100SB에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Brother PT1100SB 2 페이지. Home & project
페이지 인쇄
MODEL PT-1100
USER'S GUIDE
Printed in China
USP5069557
USP4976558
USP5009530
USP4927278
USP5120147
USP4983058
USP4839472
below:
product
this
to
related
are
which
numbers
publication
patent
and
numbers
equipment.
the
operate
to
authority
user's
the
void
Ltd.
Industries,
Brother
by
approved
expressly
not
modifications
or
help.
for
technician
radio/TV
experienced
an
or
dealer
the
connected.
is
the
which
to
that
from
different
circuit
a
on
outlet
an
to
equipment
the
receiver.
and
equipment
the
between
separation
the
antenna.
receiving
the
relocate
or
measures:
following
the
of
more
or
one
by
the
correct
to
try
to
encouraged
is
user
the
on,
and
off
equipment
by
determined
be
can
which
reception,
television
or
radio
to
interference
cause
does
equipment
this
If
installation.
particular
a
in
occur
not
will
that
guarantee
no
is
there
However,
communications.
radio
to
interference
harmful
cause
may
instructions,
the
with
accordance
in
used
and
not
if
and,
energy
frequency
radio
radiate
can
and
uses,
generates,
equipment
installation.
residential
a
in
interference
harmful
against
protection
reasonable
to
designed
are
limits
These
Rules.
FCC
the
of
15
Part
to
pursuant
device,
B
Class
a
for
limits
the
with
comply
to
found
and
tested
been
has
equipment
NOTICE
FCC
reference.
future
for
place
handy
a
and
starting
before
carefully
manual
this
read
you
that
suggest
we
use,
to
easy
is
machine
practical
extremely
an
it
make
PT-1100
the
of
performance
and
quality
the
home,
the
the
office,
the
In
printing.
professional
require
that
tasks
urgent
about
worry
to
have
colors.
exciting
and
widths
different
with
labels
print
to
you
cartridges
tape
of
variety
the
addition,
In
labels.
custom
beautiful
design
to
styles
and
frames,
many
the
from
Select
application.
any
for
labels
create
can
you
PT-1100,
INTRODUCTION
GENERAL PRECAUTIONS
•
Use only Brother TZ tapes with this machine. Do not use tapes that do not have the
mark.
•
Tapes are available in three different widths: 1/4" (6 mm), 3/8" (9 mm) and 1/2" (12
mm).
•
Do not pull the tape since this may damage the tape cassettes.
•
Do not attempt to cut the tape while printing or feeding since this will damage the
tape.
•
Do not clean the machine with alcohol or other organic solvents. Use only a soft, dry
cloth.
•
Remove the batteries and disconnect the AC adapter if you do not intend to use the
machine for an extended period of time.
Note: If power is disconnected for more than three minutes, all text shown in the
display and any text files stored in the memory will be lost.
•
Do not put any foreign objects into or anything on the machine.
•
Do not expose the machine to high temperatures or high humidity. Never leave it on
the dashboard or in the back of your car.
•
Do not use the machine in dusty places, and keep it out of both direct sunlight and
rain.
•
Do not leave any rubber or vinyl on the machine for an extended period of time.
Doing so may cause staining.
•
After inserting a new tape cassette, advance the tape by holding down
pressing
once.
•
Do not touch the print head mechanism. If the head is touched, clean it immediately
with a soft wipe (e.g., a cotton swab) to avoid permanent damage.
•
To avoid injuries, do not touch the cutter's edge.
•
Use only the AC adapter designed exclusively for this machine. Use of any
other adapter will void the warranty.
Please contact your Brother dealer for details.
POWER SUPPLY
Batteries
Since this machine is compact and portable, it can be used anywhere by installing six
AAA alkaline batteries (LR03). When changing the batteries, always replace all six at the
same time.
1 Press in on the rough area at the top end of the machine and
fold open the back cover.
2 If batteries are already installed, remove the tape cassette (if one is
LA3242001
installed) by pulling it straight out, and then remove the batteries.
3 Insert the batteries into the battery compartment with the
positive end of the bottom three batteries pointing toward the top
end of the machine, and the positive end of the top three
batteries pointing in the opposite direction.
Note: When replacing the batteries, insert the new ones within
three minutes of removing the old ones, otherwise all text
shown in the display and any text files stored in the
memory will be lost (unless the machine is plugged into
an outlet with the AC adapter).
as
are
4 Securely close the back cover, making sure that it snaps into place.
Patent
Optional AC adapter
The AC adapter allows you to use this machine wherever an electrical outlet is available.
could
Changes
-
Use Brother's AD-30 adapter for your new PT-1100.
Consult
-
1 Insert the plug on the adapter cord into the adapter jack on the bottom end of the
receiver
machine.
Connect
-
2 Insert the plug into the nearest standard electrical outlet.
Increase
-
Reorient
-
interference
the
turning
OVERVIEW
harmful
interference
Display
installed
Backspace key
This
Return key
provide
digital
Function key
This
Caps key
in
manual
the
keep
Num key
On/Off key
this
Although
machine.
or
lab
the
factory,
longer
no
You
allows
available
sizes
character
Batteries
new
your
With
Tape cassette
TAPE CASSETTES
A TZ tape cassette is supplied with this unit. The Brother TZ tapes used with this machine are
available in a variety of colors and three tape widths (1/4" (6 mm), 3/8" (9 mm) and 1/2" (12 mm)).
1 Press in on the rough area at the top end of the machine and
fold open the back cover.
2 If a tape cassette is already installed, remove it by pulling it
straight up.
3 If the ink ribbon in the other tape cassette is loose, use your
finger to wind the toothed wheel in the direction of the arrow on
the cassette until there is no slack in the ribbon. Also, make sure
that the end of the tape feeds under the tape guides.
Note: If you are using a new tape cassette provided with a
stopper, be sure to remove the stopper.
4 Insert the tape cassette firmly into the compartment, making
sure that the entire back of the cassette contacts the bottom of
the compartment.
Note: When inserting a tape cassette, make sure that the inner
ribbon does not catch on the corner of the metal guide.
5 Securely close the back cover, making sure that it snaps into place.
6 Feed the tape by holding down
and
and then push in the tape cutter lever to cut the tape.
STARTING
Press
. If batteries have been installed or the machine has been plugged in using the
optional AC adapter, the previous session's information is displayed when the machine is
turned on. This feature allows you to stop work on a label and turn off the machine, then
return to it later without having to re-enter the text.
The machine automatically turns off if no key is pressed within five minutes. The current
session's information is stored in the machine's internal memory and displayed when the
machine is later turned on again.
CODE KEY
By holding down
and pressing a key with a function, character or accent written
above it, you can use the corresponding function or add the corresponding character to
your text.
CAPS KEY
By pressing
to enter Caps mode, you can add upper-case letters to your text by
simply pressing the character keys. When this mode is on, the Caps indicator in the top-
left corner of the display comes on. To exit Caps mode, press
indicator goes off.
NUM KEY
By pressing
to enter Num mode, you can add numbers to your text by simply
pressing the corresponding keys. When this mode is on, the Num indicator in the bottom-
left corner of the display comes on. To exit Num mode, press
indicator goes off.
DISPLAY
This machine's LCD shows one row of 8 characters; however, the text that you enter can
be up to 55 characters in length. The 8-character display is like a window which moves
across the text.
1234567890123456789012345678901234567890123456789012345
Tape cutter lever
CURSOR MOVEMENT
Back cover
You can view and edit different parts of the text by moving the cursor backward and
forward.
To move the cursor one character at a time, press
To move the cursor to the beginning of the text, hold down
To move the cursor to the end of the text, hold down
Print head
BACKSPACE KEY
This key can be used to remove characters from your text, clear all of the text or cancel
the current function and return to the text input mode.
To delete the character to the left of the cursor or to cancel a function, press
To clear all of the text that is currently entered, hold down
Tape exit slot
SPACE KEY
As on a word processor, press
RETURN KEY
Press
when you wish to accept or confirm a setting, or end the first line of text and
start the second.
To add a second line, press
indicate the end of the first line and the beginning of the second.
Note: Two lines of text can only be entered if 3/8" (9-mm)- or 1/2" (12-mm)-wide tape
is installed.
To accept or confirm a setting from a list, press
ACCENTED CHARACTERS
You can also choose from a list of other accented characters that can be added to your
text.
and pressing
once,
Letter
Accented character
A
À
Á
C
Ç
E
È
É
I
Í
Ï
N
Ñ
O
Ó
Ö
U
Ù
Ú
1 Press
if you want the accented character to be an uppercase letter.
Note: To quit the following procedure at any time without making any changes, press
2 Hold down
3 Press the key for the letter in the accented character that you wish to add, and then
press
and
character.
4 Press
to add the selected character to your text.
SYMBOLS
In addition to the letters, symbols, and numerals on and above the keys, there are 72
symbols available with the Symbol function. These symbols are divided into 9 groups,
corresponding to the letters A through I.
until the Caps
Group
A
B
C
D
E
until the Num
F
G
H
I
1 Press
. The message "A-I?" appears in the display.
2 Press the key for the letter of the group containing the symbol that you wish to add,
and then press
3 Press
to add the symbol to the text.
SIZE
The characters in the text can be set to one of five different sizes in addition to AUTO,
which automatically adjusts the characters to the largest possible size according to the
width of the installed tape. The currently selected size setting is shown by the indicators at
the top of the display. All of the size indicators light up when the AUTO setting is selected.
SIZE1 (A: standard size)
or
.
A
SIZE4 (
: double width & double height)
and press
.
and press
.
Note:
• If there are two lines of text, they are printed with the SIZE1 setting applied,
regardless of the selected size setting.
• To quit the following procedure at any time without making any changes, press
1 Press
.
2 Press
and
.
current size setting appears in the display.
and press
.
3 Press
and
4 Press
(or
to add a blank space to your text.
once. The return mark (
) appears in the text to
once.
Letter
Accented character
Ä
Â
Ã
Æ
a
à
á
ä
â
ã
æ
c
ç
Ë
Ê
e
è
é
ë
ê
Î
i
í
ï
î
n
ñ
Ô
Õ
o
ó
ö
ô
õ
Ü
Û
u
ù
ú
ü
û
.
and press
. The message "A-U?" appears in the display.
until the cursor is positioned under the desired accented
Symbols
Ü
ü
Ç
ç
Æ
æ
á
é
í
ó
ú
Ã
ã
Õ
õ
Ñ
ñ
¡
¿
§
#
·
;
%
+
=
$
¢
[
]
2
3
2
3
TM
®
©
4
_
~
and
until the cursor is positioned under the desired symbol.
A
SIZE2 (A: double width)
SIZE3 (
: double height)
A
SIZE5 (
: 4 width & double height)
.
until SIZE is displayed, and then press
(or
). The
until the desired size setting is displayed.
) to apply the selected size setting to the text.