Fujitsu ScanSnap N1800 시작하기 매뉴얼 - 페이지 18
{카테고리_이름} Fujitsu ScanSnap N1800에 대한 시작하기 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Fujitsu ScanSnap N1800 23 페이지. Google docs add-in user's guide network scanner
Fujitsu ScanSnap N1800에 대해서도 마찬가지입니다: 브로셔 및 사양 (4 페이지), 소프트웨어 설명서 (22 페이지), 소프트웨어 설명서 (20 페이지)
페이지 인쇄
■ Failure to Connect to a Server
Using Its IP Address
If a server cannot be connected to by using its IP
address, or if a scanner does not respond to a ping test
by specifying its IP address, try the following:
Connection error between the server
and scanner. Or there is a problem with
the LAN cable.
■ Action
Check that the LAN cable is connected to both the
scanner and server correctly.
If the server is connected using a LAN cable (straight
type), in case Auto MDI/MDI-X (automatic selection) is
not supported, a LAN cable (crossover type), switch, or
router is required between the scanner and server.
If this is not the case, the LAN cable may be faulty. Use
a LAN cable that functions normally and try again.
IP address or subnet mask is invalid.
■ Action
On the [IP Address] window, check that the IP address
or subnet mask settings are correct.
The [IP Address] window can be displayed as follows:
1. Select [Network Settings]
When using DHCP, the DHCP server
does not operate normally. Or there is a
problem with the DHCP server settings.
■ Action
If using DHCP, on the [Network Status] window, check
that IP address, subnet mask, and default gateway
settings are all correct.
If these settings are not correct, the DHCP server may
not operate normally, or the DHCP server may not
assign valid IP addresses because of restricted number
of leases or MAC address validation.
Check the DHCP server connection status and the
details of the server settings.
The [Network Status] window can be displayed as
follows:
1. Select [Network Settings]
[Basic]
[IP Address].
[Basic]
[Network Status].
Another host or communication device
is connected using the same IP address
as the scanner.
■ Action
If the same IP address has already been used by
another host or communication device, then even if the
other device has been given a different IP address the
server may not recognize the scanner's "duplicate" IP
address until it is rebooted. Restart the server.
If a duplicate IP address connection from another host or
communication device exists on a LAN, both it will be
unusable.
If a duplicate IP address connection from another host or
communication device exists, pull out its LAN cable and
restart the server.
Access is denied due to the
establishment of a firewall between the
server and the scanner.
■ Action
If a firewall is established between the server and the
scanner, check that it is not set to deny access to the
network.
Link speed/duplex mode for the network
differs between the scanner and server.
Or the server does not support
automatic negotiation.
■ Action
Link speed/duplex mode for the network of the scanner
is set to the default setting [Auto-Negotiation].
On the [Network Status] window, match the scanner and
server's network link speed/duplex mode settings. If the
problem persists in spite of having set both the scanner
and server's network link speed/duplex settings to [Auto-
Negotiation], select something other than [Auto-
Negotiation] and check again.
On the [Network Status] window, change [Link speed/
Duplex Mode] from [Auto-Negotiation] to a fixed mode.
This can be changed as follows:
1. Select [Network Settings]
The [Network Status] window appears.
2. Select a fixed link speed/duplex mode for [Link Speed/
Duplex Mode].
3. Press the [OK] button.
18
[Basic]
[Network Status].