Fujitsu eternus af 구성 매뉴얼 - 페이지 40
{카테고리_이름} Fujitsu eternus af에 대한 구성 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Fujitsu eternus af 43 페이지. Fibre channel for citrix xenserver
Fujitsu eternus af에 대해서도 마찬가지입니다: 구성 매뉴얼 (28 페이지), 구성 매뉴얼 (25 페이지), 구성 매뉴얼 (32 페이지)
![Fujitsu eternus af 구성 매뉴얼](/uploads/products/server2/2442740/2442740.jpg)
Chapter 12
Non-disruptive Storage Migration
■
Notes
If the ALUA setting differs between the migration source and migration destination storage systems, all the
paths in the storage system where the ALUA setting is "ACTIVE / ACTIVE" and the priority paths in the storage
system where the ALUA setting is "ACTIVE-ACTIVE / PREFERRED_PATH" are set as the priority path group while
the path is connected. After the path is disconnected, the path group specified in the ALUA setting of the
migration destination storage system is used.
The following shows the path state before, during, and after the migration.
Before the migration
•
LUN PATH INFORMATION FOR LUN : /dev/rdisk/disk80
Total number of LUN paths
World Wide Identifier(WWID)
LUN path : lunpath44
Class
Instance
Hardware path
SCSI transport protocol
State
Last Open or Close state
LUN path : lunpath53
Class
Instance
Hardware path
SCSI transport protocol
State
Last Open or Close state
During the migration
•
LUN PATH INFORMATION FOR LUN : /dev/rdisk/disk80
Total number of LUN paths
World Wide Identifier(WWID)
LUN path : lunpath44
Class
Instance
Hardware path
SCSI transport protocol
State
Last Open or Close state
LUN path : lunpath53
Class
Instance
Hardware path
SCSI transport protocol
State
Last Open or Close state
LUN path : lunpath59
Class
Instance
Hardware path
SCSI transport protocol
State
Last Open or Close state
LUN path : lunpath72
Class
Instance
Hardware path
SCSI transport protocol
State
Last Open or Close state
FUJITSU Storage ETERNUS AF, ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for HP-UX
= 2
= 0x6000b5d0006a0000006a0ba0002a0000
= lunpath
= 44
= 0/0/0/7/0/0/0/5/0/0/0.0x2048000b5d6a0ba0.0x4004000000000000
= fibre_channel
= ACTIVE
= ACTIVE
= lunpath
= 53
= 0/0/0/8/0/0/0/5/0/0/0.0x2049000b5d6a0ba0.0x4004000000000000
= fibre_channel
= ACTIVE
= ACTIVE
= 4
= 0x6000b5d0006a0000006a0ba0002a0000
= lunpath
= 44
= 0/0/0/7/0/0/0/5/0/0/0.0x2048000b5d6a0ba0.0x4004000000000000
= fibre_channel
= ACTIVE
= ACTIVE
= lunpath
= 53
= 0/0/0/8/0/0/0/5/0/0/0.0x2049000b5d6a0ba0.0x4004000000000000
= fibre_channel
= ACTIVE
= ACTIVE
= lunpath
= 59
= 0/0/0/7/0/0/0/5/0/0/0.0x500000e0da120921.0x4004000000000000
= fibre_channel
= ACTIVE
= ACTIVE
= lunpath
= 72
= 0/0/0/8/0/0/0/5/0/0/0.0x500000e0da120931.0x4004000000000000
= fibre_channel
= STANDBY
= STANDBY
40
Copyright 2020 FUJITSU LIMITED
P3AM-3772-22ENZ0