Fujitsu ETERNUS DX60 설정 매뉴얼 - 페이지 3

{카테고리_이름} Fujitsu ETERNUS DX60에 대한 설정 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Fujitsu ETERNUS DX60 4 페이지. Disk storage system
Fujitsu ETERNUS DX60에 대해서도 마찬가지입니다: 사용자 설명서 (35 페이지), 사용자 설명서 (42 페이지), 설정 매뉴얼 (4 페이지), 옵션 제품 사용 (2 페이지), 구성 매뉴얼 (28 페이지), 구성 매뉴얼 (16 페이지), 옵션 제품 사용 (2 페이지), 제품 소개 (19 페이지), 패키지 내용물 (4 페이지), 매뉴얼 (4 페이지)

Fujitsu ETERNUS DX60 설정 매뉴얼
Startup
S T E P
Connect the PC to the ETERNUS DX60/DX80 with a LAN cable (for operation management), and turn on the ETERNUS DX60/
DX80.
"7.1 Setup Preparation" in the "User Guide"
n
"7.2 Basic Setup" in the "User Guide"
n
IMPORTANT
Basic Setup
S T E P
Basic ETERNUS DX60/DX80 setup is performed by accessing
the "Initial Setup" and "Configuration Wizard" functions with a
Web browser.
1.
Start the Web browser on the PC and enter either of the
following URLs in the address bar of the Web browser.
http://192.168.1.1/
https://192.168.1.1/
2.
Enter the following user name and password, and click the
[Logon] button to logon to the ETERNUS DX60/DX80.
User name: root
Password: root (Default)
3.
After logging on, the Storage System Status screen
appears.
Point

Initial Setup

Set the necessary environment for operating the ETERNUS
DX60/DX80 with its initial setup.
The [Initial Setup] screen appears by clicking the [Initial
Setup] menu on the [Easy Setup] tab.
This screen is used to set the following items:
Set Date and Time
n
Set Storage System Name
n
Change Password
n
Set SAS Port Parameters
n
Setup Network Environment
n
The first time the power is turned on, volume
formatting may start according to the factory
default settings. This does not affect the setup
operation, which may be started immediately.
When ETERNUS SF Express is used, perform
the following setup, and then refer to the
"ETERNUS SF Express User's Guide" to install
the ETERNUS DX Disk storage system.
Initial Setup
Set Date and Time
Set Storage System Name
Change Password
Setup Network Environment
Power switch
After completing these settings with the Finish step, close
the web browser to end the setup session, then detach the
direct connection LAN cable (for operation management)
from the PC and connect it to the normal network. Then
try logging on again via the normal network, using the IP
address that has just been set.
"7.2.1 Initial Setup" in the "User Guide"

Configuration Wizard

Perform the necessary settings to operate the ETERNUS
DX60/DX80 using the Configuration Wizard.
The [Configuration Wizard] screen appears by clicking the
[Configuration Wizard] button on the [Easy Setup] tab.
Create RAID Group
n
Create Volume
n
Define Host
n
"7.2.2 Configuration Wizard" in the "User Guide"
Point
Default R AID groups, volumes and af finity
groups are preset in the factory. Refer to "Web
GUI User Guide" if the preset values are to be
changed.

Assigning Hot Spares

Register hot spares for use in case the regular disks fail.
The [Assign Hot Spare] screen appears by clicking [Assign
Hot Spare] under the [RAID Group Management] menu on the
[Volume Settings] tab.
"7.2.3 Hot Spare Registration" in the "User Guide"
Point
Check the factory settings and register a hot
spare as required.
Controller
Enclosure
Configure Affinity Group
n
Define LUN Mapping
n