2N SmartGate UMTS 매뉴얼

{카테고리_이름} 2N SmartGate UMTS에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. 2N SmartGate UMTS 2 페이지.

페이지 인쇄

Calls – DialThru Gateway

By default, 2N® SmartGate UMTS behaves

as a dial-thru gateway:

• Calls are routed to UMTS/GSM from

the FXS interface.

• Incoming UMTS/GSM calls ring at the

FXS interface.

• When the FXO interface is ringing,

2N® SmartGate UMTS interconnects

FXO and FXS, thus enabling analogue

interfaces to communicate with each

other.

For more advanced call routing, you have

to program the routing tables. Some

distributors

offer

products

with

programmed routing for planned use:

• 2N® SmartGate UMTS can route calls

from the FXS interface to UMTS/GSM

and

FXO

according

the

called

number, thus cutting the outgoing call

costs significantly. Be sure to program

the FXS routing table properly using

your

and

the

PCManager

programming tool enclosed.

• ME – Mobility Extension is applied

whenever a call is coming (ringing) to

the FXO interface. With ME enabled, the

FXS and FXO lines are interconnected

and a call is set up to the defined

UMTS/GSM number. Hence, a FXO call

can be answered on the FXS interface

and/or UMTS/GSM network.

Calls – PBX Internal Line

Gateway

programming

single

parameter

assigned to the FXO routing table, you

can switch 2N® SmartGate UMTS into the

PBX internal line mode:

• Calls from the FXO interface are routed

to the UMTS/GSM network.

In the GSM network, data transfers are suspended during voice calls and

do not continue until the voice call has been finished, whereas in the

UMTS (3G) network, data and voice are transferred simultaneously.

EC Declaration of Conformity

2N TELEKOMUNIKACE a.s. hereby declares that the 2N® SmartGate UMTS product is in compliance with the

basic requirements and other relevant provisions of Directive 1999/5/EC. Refer to the CD-ROM enclosed or

www.2n.cz for the full wording of the Declaration of Conformity.

• To route incoming UMTS/GSM calls back

to the FXO interface, you also have to

set routing to FXO on the row for other

numbers in the GSM routing table. (To

make 2N® SmartGate UMTS process

calls from different UMTS/GSM callers,

complete the GSM routing table rows as

necessary.)

Configuration via USB

• To

enable

configuration

connect 2N® SmartGate UMTS to the

PC using a USB cable and install the

2N®SmartGate PCManager tool.

• Thus you create a virtual serial port

pre-

(USB

serial

port,

FTDI)

PCManager connection to the gateway

(launch CDM20814_Setup.exe to install

the drivers).

• Select the virtual serial port number in

the PCManager setup.

• Refer to the full User Manual version for

details.

Connection to Internet, SMS

• 2N® SmartGate UMTS can be used as a

modem for PC connection to GPRS,

EDGE, UMTS and HSDPA networks and

thus provide a high speed Internet

connection.

• Install the modem drivers from the

Watcher_Generic_B2849.msi file before

connecting 2N® SmartGate to the PC.

• When

2N® SmartGate

connected and switched on, the AirCard

Watcher

program

automatically, which helps you access

the Internet or send and receive SMS.

• Be sure to set APN and other provider's

settings if necessary in the connection

profile

before

connecting

Internet.

• Refer to the full User Manual version for

details.

via

PC,

for

the

UMTS

launched

the