Brother MFC-6890CDW - Color Inkjet - All-in-One 빠른 설정 매뉴얼 - 페이지 32
{카테고리_이름} Brother MFC-6890CDW - Color Inkjet - All-in-One에 대한 빠른 설정 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Brother MFC-6890CDW - Color Inkjet - All-in-One 47 페이지. Quick setup guide - spanish
Brother MFC-6890CDW - Color Inkjet - All-in-One에 대해서도 마찬가지입니다: 브로셔 및 사양 (9 페이지), 빠른 설정 매뉴얼 (49 페이지), 사양 (2 페이지), (영어) 빠른 구성 가이드 (48 페이지)
페이지 인쇄
For Wireless Network Users
16
Configure the wireless
settings using the
automatic wireless (one-
push) method
a
Confirm your wireless router/access point has
the SecureEasySetup™, Wi-Fi Protected
Setup™ or AOSS™ symbol as shown below.
b
Place the Brother machine within range of a
SecureEasySetup™, Wi-Fi Protected Setup™
or AOSS™ access point/router. The range may
differ depending on your environment. Refer to
the instructions provided with your router/access
point.
c
Push the SecureEasySetup™, Wi-Fi Protected
Setup™ or AOSS™ button on your wireless
router/access point.
See the user's guide for your wireless
router/access point for instructions.
d
On your machine, press MENU.
Press a or b to display Network and press
Network.
Press WLAN.
Press SES/WPS/AOSS.
When Switch Network interface to
wireless? is displayed, press Yes to accept.
This will start the wireless setup wizard.
To cancel, press No.
This feature will automatically detect which
mode (SecureEasySetup™, Wi-Fi Protected
Setup™ or AOSS™) your access point uses to
configure your machine.
Note
If your wireless access point supports Wi-Fi
Protected Setup™ (PIN Method) and you want to
configure your machine using the PIN (Personal
Identification Number) Method, see Using the PIN
Method of Wi-Fi Protected Setup™ in the Network
User's Guide on the CD-ROM.
32
e
If the LCD shows Connected, the machine
has successfully connected to your
router/access point. You can now use your
machine in a wireless network.
If the LCD shows Setting WLAN,
Connecting SES (Connecting WPS or
Connecting AOSS), then
Connection Failed, the machine has not
successfully connected to your router/access
point. Try starting from c again. If the same
message is indicated again, reset the machine
back to the default factory settings and try
again. For resetting, see Restore the network
settings to factory default on page 45.
If the LCD shows Setting WLAN, then
Connection Failed or Incorrect Mode, a
session overlap or connection failure was
detected (see the table below). The machine has
detected 2 or more router/access points on your
network that have the SecureEasySetup™, Wi-Fi
Protected Setup™ mode or AOSS™ mode
enabled. Make sure that only one router/access
point has the SecureEasySetup™, Wi-Fi
Protected Setup™ mode or AOSS™ mode
enabled and try starting from c again.
LCD messages when using the
SES/WPS/AOSS control panel menu
Searching or accessing the
Setting WLAN
access point and downloading
settings from the access point.
Connecting to the access
Connecting
point.
SES/WPS/AOSS
Connection failed. If this is
Connection
shown after the LCD shows
Failed
Connecting
SES/WPS/AOSS, a session
overlap was detected.
A session overlap was
Incorrect
detected.
Mode
The machine has successfully
Connected
connected.
Note
If you encounter a problem during setup,
temporarily place your machine closer to the
wireless access point, and go back to c.
Wireless setup is now complete.