Brother MFC-8950DWT 빠른 설정 매뉴얼 - 페이지 28
{카테고리_이름} Brother MFC-8950DWT에 대한 빠른 설정 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Brother MFC-8950DWT 43 페이지. Laser printers
Brother MFC-8950DWT에 대해서도 마찬가지입니다: 매뉴얼 (30 페이지), 매뉴얼 (36 페이지), 네트워크 매뉴얼 (29 페이지), 매뉴얼 (27 페이지), 빠른 설정 매뉴얼 (44 페이지), 매뉴얼 (21 페이지), 사용자 설명서 (23 페이지), 제품 안전 매뉴얼 (23 페이지)
페이지 인쇄
For Wireless Network Users
Manual setup from the control panel using the Setup Wizard
(Macintosh, mobile devices and Windows
19
Setup the wireless
settings
Important
You must have the wireless settings you wrote
down for your network in step 18-b on page 25
before you proceed.
Note
If you use your machine in an IEEE 802.1x
supported wireless network, see Using
IEEE 802.1x authentication in the Network User's
Guide.
a
If you began the wireless setup from step 5 on
page 7 (for Macintosh and mobile devices),
press Setup Wizard.
Then go to c.
All other users, go to b.
b
On your machine, press Menu.
Press a or b to display Network, and press
Network.
Press WLAN, and then Setup Wizard.
c
When WLAN Enable? is displayed, press On.
This will start the wireless setup wizard.
Otherwise press Stop/Exit to exit from the
wireless setup wizard.
d
The machine will search for available SSIDs. It
will take several seconds to display a list of
available SSIDs.
If a list of SSIDs is displayed, use a or b to
choose the SSID you wrote down in step 18-b
on page 25.
28
®
)
e
Do one of the following:
If the wireless access point/router of the
selected SSID supports WPS and The
selected access point / router
supports WPS. Use WPS? appears, go to
f.
If you are using an authentication and
encryption method that requires a Network
Key, go to g.
If your authentication method is Open
System and your encryption mode is None,
go to h.
Note
• If a list of SSIDs is not displayed, make sure
your wireless access point/router is on. Move
your machine closer to the wireless access
point/router and try starting from b again.
• If your wireless access point/router is set to not
broadcast the SSID you will have to manually
add the SSID name. For details, see
Configuring your machine when the SSID is not
broadcast in the Network User's Guide.
f
To connect your machine using the automatic
wireless mode, press Yes. (If you choose
No (Manual), go to g to enter the Network
Key.) When Start WPS on your wireless
access point / router , then press
Next. appears, press the WPS button on your
wireless access point/router, and then press
Next. Go to h.
g
Enter the Network Key you wrote down in step
18-b on page 25 using the buttons on the
Touchscreen to choose each character or
number. To delete the characters you have
entered, press
.
To enter numbers or special characters, press
repeatedly until the character you
want to enter appears, then press the character
you want.
Press
to change between upper case and
lower case.
For more information, see Entering Text for
Wireless Settings on page 34.
Press OK when you have entered all the
characters, then press Yes to apply your
settings.