Indesit BTW A51052 사용자 설명서 - 페이지 13

{카테고리_이름} Indesit BTW A51052에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Indesit BTW A51052 26 페이지.

페이지 인쇄

3 .

Add detergent

! Do not use liquid detergent for the main wash when having

activated the "Prewash" option .

! Do not use liquid detergent when selecting a later cycle start .

Add detergent (and additives/softener) into the relative

compartments as described in section "DETERGENT

DISPENSER" . Observe the dosing recommendations on the

detergent pack .

Correct dosing of detergent / additives is important, because:

• it optimizes the cleaning result

• it avoids irritating residues of surplus detergent in your

laundry

• it saves money by avoiding waste of surplus detergent

• it protects the washing machine by avoiding

calcification of components

• it respects the environment by avoiding unnecessary

environmental burden

Note: Too much detergent can result in excess foam

formation, which reduces washing efficiency . If the washing

machine detects too much foam, it may prevent spinning,

or prolong the programme duration and increase the water

consumption (see also remarks on foam formation in the

"TROUBLESHOOTING GUIDE") . Insufficient detergent may

result in grey laundry and also calcifies the heating system,

drum and hoses .

Using starch powder

• Wash your laundry in the desired wash programme .

• Prepare the starch solution according to the starch

manufacturer's instructions .

• Fill the prepared starch solution (maximum 100 ml)

into the softener chamber of the detergent dispenser .

• Close the lid and start programme "Rinse & Spin" .

4 .

Close the lid so that you can hear it click shut .

5 .

Set the desired programme

Select the required programme and temperature with the

"Programme selector" dial ("KNOB") . The washing machine

automatically indicates the default spin speed settings

possible for the selected programme . Adjust the spin speed

setting if needed with the relative button .

Change spin speed, if needed

The spin speed can be changed by pressing the "Spin speed"

button . The indicator of the predefined spin speed lights up .

Select options, if needed

Press the button to select the option; the respective button

LED indicator illuminates .

Press the button again to cancel the option; the light

extinguishes .

! When the combination of programme and additional

option(s) is not possible, the indication lights switch off

automatically .

! Unsuitable combinations of options are deselected

automatically .

Delaying the start of a programme

• To set a programme to start at a later time, see the

section "OPTIONS/ START DELAY" .

Note: To reset settings of a not yet running programme back

to its defaults press the "Reset/Drain" button .

6 .

Open water tap

Make sure that the washing machine is connected to

the water mains . Open the water tap .

7 .

Start programme

• Press the "Start/Pause"

indicator will lights up and the door will be locked .

• Due to variations in load and temperature of inlet

water, the remaining time is newly calculated in certain

programme phases .

8 .

Change the settings of a running programme, if

needed

You can still change the settings while a programme is

running . The changes will be applied, provided the respective

programme phase has not finished yet .

To change the settings of a running programme:

• Press "Start/Pause"

on pause .

• Change your settings .

• Press "Start/Pause"

programme .

If you have changed the programme, do not add

detergent for the new programme .

9 .

Pause a running programme and open the door, if

needed

• To pause the wash cycle, press the "Start/Pause"

indicator light blinks .

• If the temperature is not too high, the "Door locked"

indicator light turns off . You can open the lid, for

example to add more laundry, or to remove laundry

which was loaded by mistake . It may last a while until

you can open the lid .

• Press "Start/Pause"

again .

10 .

Cancelling a running programme, if needed

• To cancel a running programme before the end of

cycle, press the "Reset/Drain" button for at least 3

seconds .

• The water is drained out .

• It may last a while until you can open the lid .

• The water is emptied and the door unlocks at the end

of the programme .

User manual

button . The "Start/Pause"

to put the running programme

again to continue the

to proceed with the programme

, the