Indesit DFG 15B1 사용 설명서 - 페이지 26
{카테고리_이름} Indesit DFG 15B1에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Indesit DFG 15B1 28 페이지.
Indesit DFG 15B1에 대해서도 마찬가지입니다: 사용 설명서 (20 페이지), 사용 설명서 (28 페이지)
페이지 인쇄
Rinse aid and refined salt
Only use products which have been specifically designed
EN
for dishwashers.
Do not use table/industrial salt or washing-up liquid.
Follow the instructions given on the packaging.
If using a multi-functional product it is not necessary to add
any rinse aid. However, we recommend that you add salt,
especially if you live in an area where the water is hard or
(Follow the instructions given on the packaging).
very hard.
If you do not add salt or rinse aid, the LOW SALT
LOW RINSE AID indicator lights will stay lit.
Measuring out the rinse aid
Rinse aid makes it easier for the crockery to dry, as water runs off
the surfaces more readily and therefore does not leave streaks
or marks. The rinse aid dispenser should be filled:
• When the LOW RINSE AID indicator light
is illuminated, a reserve supply of rinse aid is still available
for 1-2 cycles;
1. Open the dispenser
on the lid;
2. Carefully introduce the rinse aid as far as the maximum
reference notch of the filling space - avoid spilling it. If this
happens, clean the spill immediately with a dry cloth.
3. Press the lid down until you hear a click to close it.
NEVER pour the rinse aid directly into the appliance tub.
Rinse-aid dispenser setting
If you are not completely satisfied with the drying results, you
can adjust the quantity of rinse aid. Switch on the dishwasher
using the ON/OFF button, wait a few seconds and switch it off
using the ON/OFF button. Press the Start/Pause button 3 times;
switch on the machine using the ON/OFF button and access
the adjustment menu - the rinse-aid indicator light is lit
factory level).
Adjust the level of rinse aid supply using the WASH CYCLE
SELECT knob. There is a rinse aid level for each wash cycle
(0 to 4 max).
Press the ON/OFF button to save the setting.
If the rinse aid level is set to ZERO (ECO), no rinse aid will be
supplied. The LOW RINSE AID indicator light will not be lit if you
run out of rinse aid.
• If there are streaks on the crockery, set a low number (1-2).
• If there are drops of water or limescale marks, set a high
number (3-4).
Setting water hardness
Every dishwasher is equipped with a water softener which, by
using refined salt designed specially for this type of appliance,
supplies water without limescale which is then used to wash
the crockery.
This dishwasher has a setting that helps reduce pollution and
optimises washing performance in accordance with the water
hardness level in your area. Ask your local water supplier for
this information.
26
*
on the control panel
"D"
by pressing and pulling up the tab
- Switch on the dishwasher using the ON/OFF button, wait a
few seconds and switch it off using the ON/OFF button. Hold
down the Start/Pause button for min. 3 seconds; switch on the
machine using the ON/OFF button and access the adjustment
menu - the salt indicator light is lit.
-Select the desired level using the SELECT WASH CYCLE knob
*
(1 to 5
Max.)
(water softener set to medium level).
Press the ON/OFF button to save the setting.
Even if using multi-functional tablets, fill the salt dispenser.
*
and
Water Hardness Table
Level
°dH
1
0 - 6
2
6 - 11
3 12 - 17
4 17 - 34
*
34 - 50
5
For values between 0°f and 10°f, we do not recommend the
*
use of salt.
this setting may cause a slight increase in the
duration of the cycles. ** for 1 wash cycle per day.
(°dH = hardness measured in German degrees - °f = hardness
measured in French degrees – mmol/l = millimoles per litre)
Measuring out the refined salt
In order to obtain the best possible results from a wash cycle,
make sure that the salt dispenser is never empty.
Refined salt removes limescale from the water, thus avoiding
the formation of deposits on crockery.
The salt dispenser is located in the lower part of the dishwasher
(see Description)
• When the green float
the cap of the salt dispenser;
• When the LOW RINSE AID indicator light on the control panel
*
is illuminated
(set to
1 kg). It is normal for a little water to leak out.
4. Remove the funnel* and wipe any salt residues away from
the opening; rinse the cap under running water and then screw
it on, the head facing downwards so as to let the water flow out
of the four slots (star-shaped arrangement) in the lower part of
the cap (cap with green float
It is advisable to perform this procedure every time you add
salt to the dispenser.
Make sure the cap is screwed on tightly so that no detergent can
get into the container during the wash cycle (this could damage
the water softener beyond repair).
When necessary, measure out the salt before a wash cycle
so that any saline solution which has leaked out of the salt
dispenser is removed.
*
Only available in selected models.
Average salt container
capacity duration
°fH
mmol/l
months
0 - 10
0 - 1
7 months
11 - 20
1,1 - 2
5 months
21 - 30
2,1 - 3
3 months
31 - 60
3,1 - 6
2 months
61 - 90
6,1 - 9
2/3 weeks
and should be filled:
*
cannot be seen by simply looking at
;
1. Remove the lower rack and unscrew the
cap (anticlockwise).
2. The first time you do this: fill the water tank
right up to its edge.
*
(see figure)
3. Position the funnel
salt dispenser up to the edge (approximately
*
).
**
and fill the