Indesit IDF 145 사용 설명서 - 페이지 2

{카테고리_이름} Indesit IDF 145에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Indesit IDF 145 16 페이지.

페이지 인쇄

Installation

Keep this instruction manual in a safe place for future

reference. If the appliance is sold, given away or moved,

please ensure the manual is kept with the machine, so that

the new owner may benefit from the advice contained within

it.

Please read this instruction manual carefully: it contains

important information regarding the safe installation, use

and maintenance of the appliance.

If the appliance must be moved at any time, keep it in

an upright position; if absolutely necessary, it may be tilted

onto its back.

This appliance is intended to be used in household

and similar applications such as:

- staff kitchen areas in shops, offices and other working

environments;

- farm houses;

- by clients in hotels, motels and other residential type

environments;

- bed and breakfast type environments.

Positioning and levelling

1. Remove the appliance from all packaging and check

that it has not been damaged during transportation.

If it has been damaged, contact the retailer and do not

proceed any further with the installation process.

2. Check the dishwasher by placing it so that its sides or

back panel are in contact with the adjacent cabinets or

even with the wall. This appliance can also be recessed

under a single worktop

sheet ).

3. Position the dishwasher on a level and sturdy floor. If the

floor is uneven, the front feet of the appliance may be

adjusted until it reaches a horizontal position. If the

appliance is levelled correctly, it will be more stable and

much less likely to move or cause vibrations and noise

while it is operating.

4. Adjust the height of the rear foot from the front of the

appliance

on the central lower part of the dishwasher,

turning a hexagonal spanner (red color) with an opening

of 8 mm in a clockwise direction to increase the height or

in an anticlockwise direction to decrease the height.

Connecting the water and electricity

supplies

Connection to the water and electricity supplies should

only be performed by a qualified technician.

The dishwasher should not stand on top of the water

hoses or the electricity supply cable.

The appliance must be connected to the water supply

network using new hoses.

Do not use old hoses.

The water inlet and outlet hoses and the electricity supply

cable may be positioned towards the right or the left in

order to achieve the best possible installation.

( see the Assembly instruction

Connecting the water inlet hose

• To a suitable cold water connection point: before

attaching the hose, run the water until it is perfectly clear

so that any impurities that may be present in the water

do not clog the appliance; after performing this

operation, screw the inlet hose tightly onto a tap with a

¾ gas threaded connection.

• To a suitable hot water connection point: your

dishwasher may be supplied with hot water from the

mains supply (if you have a central heating system with

radiators) provided that it does not exceed a temperature

of 60°C.

Screw the hose to the tap as described for connection

to a cold water supply.

If the inlet hose is not long enough, contact a specialist

store or an authorised technician ( see After Sales Service ).

The water pressure must be within the values indicated

in the Technical data table ( see adjacent information ).

The hose should not be bent or compressed.

Connecting the water outlet hose

Connect the outlet hose (without bending it) to a drain duct

with a minimum diameter of 4 cm.

The outlet hose must be at a height ranging from 40 to 80

cm from the floor / surface where the dishwasher rests (A).

Before connecting the water outlet hose to the sink drain,

remove the plastic plug (B).

Anti-flooding protection

To ensure floods do not occur, the dishwasher:

- is provided with a special system which blocks the water

supply in the event of anomalies or leaks from inside the

appliance.

Some models are also equipped with the supplementary

safety device New Acqua Stop

flooding protection even in the event of a supply hose

rupture.

WARNING: HAZARDOUS VOLTAGE!

Under no circumstance should the water inlet hose be cut

as it contains live electrical parts.

Only available in selected models.

, which guarantees anti-