Indesit FG10(BK) 설치 및 사용 설명서 지침 - 페이지 6

{카테고리_이름} Indesit FG10(BK)에 대한 설치 및 사용 설명서 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. Indesit FG10(BK) 18 페이지. Gas built in single oven

페이지 인쇄

1. Using the Oven

Introduction

Glass door panels

To meet the relevant Standards of

Domestic cooking appliances, all the

glass panels on this appliance are

toughened to meet the fragmentation

requirements of BS3193. This ensures

that, in the unlikely event that a panel

breaks, it does so into small fragments

to minimise the risk of injury.

Please take care when handling, using

or cleaning all glass panels as any

damage to the surfaces or edges may

result in the glass breaking without

warning or apparent cause at a later

date.

Should any glass panel be

damaged, we strongly recommend

that it is replaced immediately.

Before using the appliance for

the first time, remove any protective

polythene film and wash the oven

shelves in hot soapy water to remove

their protective covering of oil. Even

so, when you first switch on the oven

or grill you may notice a smell and

some smoke.

Condensation

When hot and cold air meet,

condensation forms. The outer door is air

cooled and the inner door gets hot, so some

condensation might form; this is normal

and will disappear within 10 - 15 minutes.

To replace a light bulb (if fitted)

Caution: Switch off the electricity

supply to the appliance, to avoid the

possibility of electric shock.

Wait until the oven is cool, then

remove the shelves.

Unscrew

the

lens

cover

anticlockwise). Unscrew the bulb and

replace. Replace lens cover.

Please note that light bulbs are not

covered by guarantee.

Environmental Protection

We are committed to protecting the

environment

and

operate

Environmental Management System

which complies with BS EN ISO

14001:1996.

Disposal of packaging

All our packaging materials are

recyclable and environmentally

friendly.

Please help us to protect our

environment by disposing of all

packaging in an environmentally

friendly manner.

Please contact your local authority

for the nearest recycling centre.

Caution: Packaging materials can

pose a risk of suffocation - keep away

from children.

Step 5: Commissioning

Pressure test point

Use the oven burner. From inside the

oven remove the burner cowl. Remove

the small screw at the LHS of the

(turn

burner cradle. Slide the burner to the

left to access the injector.

Connect

suitable

(incorporating a 1.25mm injector) to

the injector.

Connect manometer to

the T-piece, and turn oven control to

full on to check pressure.

Replace in reverse order.

Burner aeration

All burners have fixed aeration and no

adjustment is possible.

Pressure setting

Cat I

G20 Natural Gas @ - 20mbar

Electrical systems check

In the event of an electrical fault the

preliminary electrical system check

(earth continuity, short circuit, polarity

and resistance to earth) must be

carried out.

Installation Instructions

Oven

1. Push in and turn the control knob

anticlockwise to gas mark 9.

2. Adjust to the required setting.

3. The burner may not come on to a

full rate unless the oven door is

closed.

The oven burner operates at a low

T-piece

rate for up to 60 seconds until the

flame supervision device opens

and full gas rate is obtained.

Grill

1. The door must be open for the grill

burner to ignite.

2. Push in and turn the control knob

clockwise to the grill symbol.

3. Close the door, and check that the

burner goes out.

The grill burner will re-ignite when

the door is opened again.

Before leaving the installation

Show the customer how to ignite

the oven and grill and give them this

handbook. Thank you.