Indesit KN6G210S/I 사용 설명서 - 페이지 19

{카테고리_이름} Indesit KN6G210S/I에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Indesit KN6G210S/I 48 페이지. Cooker and oven
Indesit KN6G210S/I에 대해서도 마찬가지입니다: 사용 설명서 (44 페이지)

페이지 인쇄

• Is easy to inspect along its whole length so that its

condition may be checked.

• Is shorter than 1500 mm.

• Fits firmly into place at both ends, where it will

be fixed using clamps that comply with current

regulations.

! If one or more of these conditions is not fulfilled

or if the cooker must be installed according to the

conditions listed for class 2 - subclass 1 appliances

(installed between two cupboards), the flexible steel

hose must be used instead (see below).

Connecting a flexible jointless stainless steel pipe

to a threaded attachment

Make sure that the hose and gaskets comply with

current national legislation.

To begin using the hose, remove the hose holder on

the appliance (the gas supply inlet on the appliance is

a cylindrical threaded 1/2 gas male attachment).

! Perform the connection in such a way that the hose

length does not exceed a maximum of 2 metres,

making sure that the hose is not compressed and does

not come into contact with moving parts.

Checking the tightness of the connection

When the installation process is complete, check the

hose fittings for leaks using a soapy solution. Never

use a flame.

Adapting to different types of gas

It is possible to adapt the appliance to a type of gas

other than the default type (this is indicated on the

rating label on the cover).

Adapting the hob

Replacing the nozzles for the hob burners:

1. Remove the hob grids and slide the burners off their

seats.

2. Unscrew the nozzles using a 7

mm socket spanner (see fi gure),

and replace them with nozzles

suited to the new type of gas (see

Burner and nozzle specifi cations

table).

3. Replace all the components

by following the above

instructions in reverse.

Adjusting the hob burners' minimum setting:

1. Turn the tap to the minimum position.

2. Remove the knob and adjust the regulatory screw,

which is positioned inside or next to the tap pin, until

the flame is small but steady.

! If the appliance is connected to a liquid gas supply,

the regulatory screw must be fastened as tightly as

possible.

3. While the burner is alight, quickly change the position of

the knob from minimum to maximum and vice versa several

times, checking that the flame is not extinguished.

! The hob burners do not require primary air

adjustment.

Adapting the oven

Replacing the oven burner nozzle:

1. Open the oven door fully

2. Pull out the sliding oven

bottom (see diagram).

3. Remove the oven burner

after unscrewing the screws V

(see fi gure).

4. Unscrew the nozzle using a

special nozzle socket spanner

(see fi gure) or with a 7 mm

socket spanner, and replace it

with a new nozzle that is suited

to the new type of gas (see

Burner and nozzle specifi cations

table).

Adjusting the gas oven burner's minimum setting

1. Light the burner (see Start-up and Use).

2. Turn the knob to the minimum position (MIN)

after it has been in the maximum position (MAX) for

approximately 10 minutes.

3. Remove the knob.

4. Tighten or loosen the adjustment screws on the

outside of the thermostat pin (see fi gure) until the flame

is small but steady.

! If the appliance is connected to liquid gas, the