Indesit DD60C2C /UK 사용 설명서 - 페이지 20

{카테고리_이름} Indesit DD60C2C /UK에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Indesit DD60C2C /UK 28 페이지. Free standing electric cooker

페이지 인쇄

Care and Cleaning

Control Panel:

Wipe with a damp cloth and polish with a dry cloth.

Stainless trims

Regularly wipe with a clean, damp cloth and polish

with a clean dry cloth.

Grill Door:

Wipe over the grill door decorative outer panel; with

a cloth wrung out in warm soapy water, then after

wiping with a cloth wrung out in clear water, dry with

a soft clean cloth.

Do not use scouring pads or abrasive powder

which may scratch the surface.

Ensure that the glass panel (where fitted) is not

subjected to any sharp mechanical blows.

Grill:

Remove the grill pan and the wire grid food support,

it is best to wash these items immediately after each

use to prevent stains from being burnt on when used

again. Wipe out the Grill compartment, use a fine

steel wool soap pad to remove stubborn stains from

the compartment.

Main oven:

1. Glass Door - open the oven door fully.The glass

panel may now be cleaned. Stubborn stains can

be removed by using a fine steel wool soap pad.Do

not use scouring pads, or abrasive powder, which

will scratch the glass. Ensure that the glass panel

is not subjected to any sharp mechanical blows.

For slight soiling the inner glass panel may be

cleaned, while still warm. For removing stubborn

stains see "Care and Cleaning" chapter.

2. Remove the rod shelves and meat pan. Use a fine

steel wool soap pad to remove stubborn stains from

the rod shelves,meat pan and the floor of the oven.

Refer to the instructions in "Care and Cleaning"

chapter, for cleaning the shelf supports. Do not use

aerosol cleaners on this oven as they could

adversely affect the fan motor unit, and cannot be

wiped off the fan blade.

Replacement oven lamp:

WARNING: To avoid electric shocks - please

ensure that the electricity supply to the appliance

is switched off and the appliance is fully cold,

before removing the lamp lens.

Open the oven door and remove the rod shelves.

Using a suitable cloth to protect the fingers grip the

light glass dome, unscrew anti-clockwise and lift.

Reach into the aperture and unscrew the lamp anti-

clockwise. Fit replacement lamp (25W 300°C rated

SES), refit dome.

Wall-mounted splash panel:

A wall-mounted splash panel is available as an

optional extra from our Parts Department (see Key

Contacts, back page).

Care must be taken that rating label edges are not

lifted during cleaning and furthermore that the

lettering is not blurred or removed. For details of

your nearest Service Centre please see the separate

service leaflet. If you have any queries regarding

service or spares, our Parts and Service Division will

be pleased to advise.

See Key Contacts, back page, for details.

Take particular care not to damage the inner

surface of the door inner glass that is coated with

a heat reflective layer.Do not use scouring pads,

or abrasive powder, which will scratch the glass.

Ensure that the glass panel is not subjected to

any sharp mechanical blows.

Stubborn stains can be removed by using a fine steel

wool pad. For slight soiling the inner glass panel may

be cleaned, while still warm, without removing it from

the door. After cleaning, rinse and dry with a soft cloth.

CLEANING THE DOORS

SIDE OPENING DOORS

Cleaning the door glass is the same as the drop

down doors,except take care to support the weight

of the inner glass when removing and refitting.

DROP DOWN DOORS

Remove the door inner glass as follows.

1. Open the door fully and unscrew the two screws

securing the glass panel so that the securing

brackets can be turned.There is no need to remove

the screws completely.

2. Turn the brackets so that the glass can be removed

and cleaned at the sink (Fig. 1.)

3. The inside of the outer door glass can now be

cleaned while still fitted to the cooker.

NEVER OPERATE THE COOKER

WITHOUT THE INNER DOOR GLASS IN

POSITION.

Refit the door inner glass as follows.

1.Turn the two securing

brackets back to their original

position to retain the glass and

tighten the screws. (Fig. 2.)