Indesit ID6IVS2/UK 사용 설명서 - 페이지 23

{카테고리_이름} Indesit ID6IVS2/UK에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Indesit ID6IVS2/UK 28 페이지. Free standing electric cooker

페이지 인쇄

Care and Cleaning

Control Panel:

Wipe with a damp cloth and polish with a dry cloth.

Stainless trims

Regularly wipe with a clean, damp cloth and polish with

a clean dry cloth.

Grill Door:

Wipe over the grill door decorative outer panel; with a

cloth wrung out in warm soapy water, then after wiping

with a cloth wrung out in clear water, dry with a soft clean

cloth.

Do not use scouring pads or abrasive powder which

may scratch the surface.

Ensure that the glass panel (where fitted) is not

subjected to any sharp mechanical blows.

Grill:

Remove the grill pan and the wire grid food support, it

is best to wash these items immediately after each use

to prevent stains from being burnt on when used again.

Wipe out the Grill compartment, use a fine steel wool soap

pad to remove stubborn stains from the compartment.

Main oven:

1. Glass Door - open the oven door fully.The glass

panel may now be cleaned. Stubborn stains can be

removed by using a fine steel wool soap pad.Do not

use scouring pads, or abrasive powder, which will

scratch the glass. Ensure that the glass panel is not

subjected to any sharp mechanical blows. For slight

soiling the inner glass panel may be cleaned, while

still warm. For removing stubborn stains see "Care

and Cleaning" chapter.

2. Remove the rod shelves and meat pan. Use a fine

steel wool soap pad to remove stubborn stains from

the rod shelves,meat pan and the floor of the oven.

Refer to the instructions in "Care and Cleaning" chap-

ter, for cleaning the shelf supports. Do not use aerosol

cleaners on this oven as they could adversely affect

the fan motor unit, and cannot be wiped off the fan

blade.

Replacement oven lamp:

WARNING: To avoid electric shocks - please ensure

that the electricity supply to the appliance is switched

off and the appliance is fully cold, before removing

the lamp lens.

Open the oven door and remove the rod shelves. Using

a suitable cloth to protect the fingers grip the light glass

dome, unscrew anti-clockwise and lift. Reach into the

aperture and unscrew the lamp anti-clockwise. Fit

replacement lamp (25W 300°C rated SES), refit dome.

Wall-mounted splash panel:

A wall-mounted splash panel is available as an optional

extra from our Parts Department (see Key Contacts,

back page).

Care must be taken that rating label edges are not lifted

during cleaning and furthermore that the lettering is not

blurred or removed. For details of your nearest Service

Centre please see the separate service leaflet. If you have

any queries regarding service or spares, our Parts and

Service Division will be pleased to advise.

See Key Contacts, back page, for details.

Take particular care not to damage the inner surface

of the door inner glass that is coated with a heat

reflective layer.Do not use scouring pads, or abrasive

powder, which will scratch the glass. Ensure that the

glass panel is not subjected to any sharp mechanical

blows.

Stubborn stains can be removed by using a fine steel

wool pad. For slight soiling the inner glass panel may

be cleaned, while still warm, without removing it from

the door. After cleaning, rinse and dry with a soft cloth.

CLEANING THE DOORS

SIDE OPENING DOORS

Cleaning the door glass is the same as the drop down

doors,except take care to support the weight of the

inner glass when removing and refitting.

DROP DOWN DOORS

Remove the door inner glass as follows.

1. Open the door fully and unscrew the two screws se-

curing the glass panel so that the securing brackets

can be turned.There is no need to remove the screws

completely.

2. Turn the brackets so that the glass can be removed

and cleaned at the sink (Fig. 1.)

3. The inside of the outer door glass can now be cleaned

while still fitted to the cooker.

NEVER OPERATE THE COOKER WITHOUT

THE INNER DOOR GLASS IN POSITION.

Refit the door inner glass as follows.

1.Turn the two securing bra-

ckets back to their original

position to retain the glass and

tighten the screws. (Fig. 2.)