Indesit IT50L 사용 설명서 - 페이지 5

{카테고리_이름} Indesit IT50L에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Indesit IT50L 24 페이지. Indesit it50g s; it50g1 s; it50l s; it50g1; it50l; it50g; itl50g1; itl50gm; itl50ga; itl50gw 50cm free standing gas cooker
Indesit IT50L에 대해서도 마찬가지입니다: 사용 설명서 (24 페이지)

페이지 인쇄

Connection of the appliance to the gas mains or liquid

gas must be carried out according to the prescribed

regulation in force, and only after it is ascertained that it

is adaptable to the type of gas to be used. If not, follow

the instructions indicated in the paragraph headed

"Adaptation to different gas types". On some models

the gas supply can be connected on the left or on the

right, as necessary; to change the connection, reverse

the position of the hose holder with that of the cap

and replace the gasket (supplied with the appliance).

In the case of connection to liquid gas, by tank, use

pressure regulators that conform to the regulation in

force. The gas supply must be connected to the left

of the appliance. Be sure that the hose does not pass

through the rear of the cooker touching hot parts.

! make sure the supply pressure conforms

with the values shown in the table entitled

"Caracteristics of the burners and nozzles".

When the cooker is installed between cabinets

(recessed), the gas connection must be effected

by an approved flexible hose with bayonet fitting

(BS 669 Current Edition). The gas inlet for the

cookers is a threaded G 1/2 gas female fitting.

Connecting the gas supply

To make the connection, a flexible hose should be

used corresponding to the current gas regulations

which are:

• the hose must never be at any point in its lenght in

contact with the "hot" parts of the cooker;

• the hose must never be longer than 1,5 metre;

• the hose must not be subject to any tension or

torsional stress and it must not have any excessively

narrow curves or bottlenecks;

• the hose must be easy to

HOT PARTS

inspect along its entire length to

check its condition;

• the hose must always be in

good condition, never attempt

to repair.

! the installation must comply

with gas safety (installation and use) regulations 1984.

In all cases for the above, by low, a qualified, gas safe

approved engineer must be called for installation.

Electrical connection

Power supply voltage and frequency: 230-240V a.c.

50Hz.

! the supply cable must be positioned so that it never

reaches at any point a temperature 50°C higher than

the room temperature. The cable must be routed away

from the rear vents. Should you require it, you may

use a longer cable, however, you must ensure that the

cable supplied with the appliance is replaced by one

of the same specifications in accordance with current

standards and legislation.

Your appliance is supplied with a 13 amp fused

plug that can be plugged into a 13 amp socket for

immediate use. Before using the appliance please read

the instructions below.

WARNING - THIS APPLIANCE MUST BE EARTHED.

THE FOLLOWING OPERATIONS SHOULD BE

CARRIED OUT BY A QUALIFIED ELECTRICIAN.

Replacing the fuse

When replacing a faulty fuse, a 13 amp ASTA

approved fuse to BS 1362 should always be used, and

the fuse cover re-fitted. If the fuse cover is lost, the

plug must not be used until a replacement is obtained.

Replacement fuse covers:

If a replacement fuse cover is fitted, it must be of the

correct colour as indicated by the coloured marking

or the colour that is embossed in words on the base of

the plug. Replacements can be obtained directly from

your nearest Service Depot.

Removing the plug:

If your appliance has a non-rewireable moulded plug

and you should wish to remove it to add a cable

extension or to re-route the mains cable through

partitions, units etc., please ensure that either:

• the plug is replaced by a fused 13 amp re-wireable

plug bearing the BSI mark of approval.

or:

• the mains cable is wired directly into a 13 amp cable

outlet, controlled by a switch, (in compliance with

BS 5733) which is accessible without moving the

appliance.

Please note: for appliances with a rating greater

than 13 amp (eg: electric hob, double ovens and

freestanding electric cookers etc.) the mains cable

must be wired into a cooker output point with a rating

of 45 amp. In this case the cable is not supplied.

Disposing of the plug:

Ensure that before disposing of the plug itself,

you make the pins unusable so that it cannot be

accidentally inserted into a socket. Instructions for

connecting cable to an alternative plug:

! the wires in the mains lead are coloured in

accordance with the following code:

Green & Yellow - Earth

Blue

- Neutral